Our Brands

Development Boards

78 - 92
86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
94 - 108
Newest Items First
15 Per Page
MOD-TXS0102 2-bit Bi-directional Voltage Level Converter I2C Level module
US$6.92
This two-bit non-inverting translator is a bidirectional voltage-level translator and can be used to establish digital switching compatibility between mixed-voltage systems. It uses two separate configurable power-supply rails, with the A ports supporting operating voltages from 1.65 to 3.6 VDC while it tracks the VCCA supply and the B ports supporting operating voltages from 2.3 to 5.5 VDC while it tracks the VCCB supply. This allows the support of both lower and higher logic signal levels while providing bidirectional translation capabilities between any of the 1.8 V, 2.5 V, 3.3 V, and 5 V voltage nodes.
In stock
+ −
Add to wish list
BB-SW1 ON/OFF Latching Pushbutton Breakout-Board
US$1.53
This miniature latching pushbutton is a ON/OFF switch that can be mounted and soldered on the included breakout-board (which is breadboard compatible). The two holes on the sides allow for mounting the breakout-board using M3 screws. The way the locking mechanism works is that once the button is pressed it locks and stays in the locked position. Pressing the button once again will unlock the mechanism and release the button.
In stock
+ −
Add to wish list
MOD-AD9833 AD9833 - Programmable Waveform Generator breakout board for Arduino
US$15.32
The AD9833 is a low power, programmable waveform generator capable of producing sine, triangular, and square waveform outputs. Simply connect the device using SPI wiring on the Uno or any microcontroller that supports SPI and program the device to store the waveform coordinates to be displayed on a TFT LCD purchased separately.
In stock
+ −
Add to wish list
ARD-NANO-B1 D.I.Y Arduino Nano Breakout Board
US$4.61
This is a diy Arduino Nano breakout board. The package includes 2x15-pin female headers, which allows you to connect your Arduino Nano onto this breakout board. This kit also comes with 10x3-pin screw terminal blocks which allow you to connect 22-18 AWG wires (10A max). An Arduino Nano is required for this kit.
In stock
+ −
Add to wish list
ARD-FTDI-5V3IO FTDI Cable with 5V power and 3.3V logic
US$12.76
This is a special FTDI cable, usually you can get either 5v or 3.3v based on the FT232R chip. This means that the data and power cable is only 5v or 3.3vdc. This product offers the red and black cable to provide 5VDC and the data lines white, green, yellow and blue run on 3.3vdc.  This cable is excellent for running your raspberry pi that requires 5vdc to power on and 3.3vdc for logic pins.
In stock
+ −
Add to wish list
BB-24C256 256KB I2C EEPROM for 5V microcontrollers
US$3.07
This product is an excellent choice for those who don’t have enough memory space for their microcontroller based projects. An EEPROM acts like a memory card where you can save data onto the device up to 256KB and it will retain that information even when power is lost! Simply connect four wires to get this device up and running by I2C protocol. It is recommended to run the Arduino i2C scanner to code to find the address of this device. You can attach more EEPROM and address them for more memory.
In stock
+ −
Add to wish list
MOD-74HC595 Two Seven Segment Display Breakout Board
US$4.54
This is a simple board with two Seven Segment Display soldered onto the board and some through holes for soldering pins. This board has two shift registers, SM74HC595D to drive each seven segment display reducing the amount of wiring you need to have the displays functional. The only wiring you need to do is supply 5v, GND, SDI to pin 8 on Arduino, SCLK to pin 10 and LOAD to pin 9 on Arduino. You can also daisy chain These displays by connecting P2 to the new board P1.
In stock
+ −
Add to wish list
STM32F030F4P6 Cortex-M0 From STLINK (STM32F030F4P6) Development Board
US$9.05
This board is a STM32F030F4P6 Development Board also known as the Cortex-M0. It is a ARM 32-bit Cortex-M0 CPU with a frequency up to 48 MHz and features a high-speed embedded memory. As a minimal ready-to-run system, this board has a Micro USB power supply interface, ISP/SWD programming/debugging interface, boot mode selection and etc., It also comes with some headers and requires some soldering to get them inserted on.
In stock
+ −
Add to wish list
WEMOS-POWER Power Shield for WeMos D1 Mini
US$7.69
The WeMos D1 Mini is based on the ESP8266 microcontroller with WiFi. This shield gives the WeMos D1 Mini the ability to accept power from 7 to 14Vdc via a 2.1mm DC jack or screw terminals that requires soldering. This board is excellent to run you WeMos mini without the need of a USB cable and supply currents up to 1Amp.
In stock
+ −
Add to wish list
WEMOS-OLED WeMos OLED Development Board
US$30.72
This is a simple microcontroller designed around the ESP8266 chip. This board also comes with a 0.96 inch OLED display, a pushbutton a battery holder for 18650 battery. Use this device as slave and communicate from your mobile device to activate relays, read values or any other ideas you may have from ~10 meters. It comes with a 10-bit Analog to Digital Converter, wireless channel is around 2.4Ghz and supports WPA/WPA2 encryption under wifi protocols b/g/n its' operating voltage is 3.0 ~ 3.6V and has 4 MB of Flash storage. Great component for industrial applications, home automation, beacon tracker, etc,. Supports Arduino IDE!
Delivery within 2-3 weeks
+ −
Add to wish list
WAVE-342 FT245 EVAL BOARD
US$22.25
The FT245 EVAL BOARD provides a high-performance cost-effective solution for USB TO 8-BIT FIFO. It is based on the FT245RL chip and will hopefully allow to try out the full potential of the FT245 device before using it in your prototype. The FT245RL is a USB to parallel FIFO interface device which simplifies USB to FIFO designs and reduces external component count by fully integrating an external EEPROM, USB termination resistors and an integrated clock circuit which requires no external crystal, into the device. It has been designed to operate efficiently with a USB host controller by using as little as possible of the total USB bandwidth available.
In stock
+ −
Add to wish list
WAVE-4655 FT245 USB FIFO Board (type A)
US$15.39
The FT245 USB FIFO Board (type A) is an accessory board that provides a USB to parallel FIFO interface, with FT245 chip onboard, also features USB Type A connector, and control interface (8 data pins & 6 control pins). The FT245 USB FIFO Board (type A) is ideal for establishing communication between MCU and PC. There is also a jumper used for selecting VCC output level provided on the board.
In stock
+ −
Add to wish list
WAVE-4654 FT245 USB FIFO Board (mini)
US$15.39
The FT245 USB FIFO Board (mini) is an accessory board that provides a USB to parallel FIFO interface, with FT245 chip onboard, also features USB mini-AB connector, and control interface (8 data pins & 6 control pins). The FT245 USB FIFO Board (mini) is ideal for establishing communication between MCU and PC. There is also a jumper used for selecting VCC output level provided on the board.
In stock
+ −
Add to wish list
MOD-ATTINY85 ATTINY85 Compatible Microcontroller
US$18.36
The ATTiny, one of the most useful microcontrollers you can get your hands on. Due to the footprint of this component you can find these microcontrollers on any wearable projects. They are also very inexpensive, this product comes with the features of the ATTiny on a simple board with Micro USB port and some headers for easy interfacing and programming. These ATTiny are commonly used for RGB LEDs based projects. They also come with a voltage regulator allowing you to supply external voltage from 7-12VDC. You will only get access to 6 pins and the ATTINY is surface mounted on this board.
In stock
+ −
Add to wish list
DFR0416 Bluno M0 Mainboard
US$43.75
Bluno M0 is the only ARM Cortex-M0 Arduino Microcontroller that supports 5V standard logic level. With built-in Bluetooth chip, Bluno M0 supports multi-functions such as Bluetooth communication, wireless programming. Have you tried to make projects with traditional Arduino board? Although these boards have better compatibility, but when you want to make volume production, you'll find that these boards are lacking of pins, low-performance or not compatible with 5V operating voltage. And most of them are very expensive. Luckily, Bluno M0 is a great soul solves all. Bluno M0 selects 32-bit Nuvoton high-performance SCM (Single Chip Micyoco) as the core. Besides built-in ARM Cortex M0 infrastructure, Bluno M0 supports 5V Logic level, equipped with 1 USB port and 2 serial ports, providing 31 digital pins (parts AFIO) and 6 analog pins, offering more IO resources. Moreover, Bluno M0 is compatible with Arduino Leonardo package/encapsulation and the clock speed is 72MHz. Additionally, Bluno M0 supplies another IIS interface, supporting play &record wav files. Once put Bluno M0 with advanced IIS chip, professional HIFI audio is available.
In stock
+ −
Add to wish list
78 - 92
86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
94 - 108