Our Brands

Development Boards

101 - 115
109 110 111 112 113 114 115 116 117 118 119 120 121 122 123
117 - 131
Newest Items First
15 Per Page
PI2-CASE-BLACK Raspberry Pi 2 Enclosure - Black
US$10.71

This black case for the Raspberry Pi2 provides slots to access the peripheral header, USB ports, Ethernet, SD card, HMDI, composite video, audio, CSI and JTAG connectors as well as feet and vents to ensure the board gets proper cooling and plus-shaped wall mounting slots.

In stock
+ −
Add to wish list
ARD-MEGA Arduino Mega2560 Compatible Development Board
US$31.80
This is an Arduino compatible R3 Mega2560 ATmega2560-16AU control board. Comes with USB cable.
In stock
+ −
Add to wish list
WRL-12938 SparkFun FM Tuner Evaluation Board - Si4703
US$36.03
This is an evaluation board for the Silicon Laboratories Si4703 FM tuner chip. Beyond enabling you to tune in to FM radio stations, the Si4703 is also capable of detecting and processing both Radio Data Service (RDS) and Radio Broadcast Data Service (RBDS) information. The Si4703 even does a very good job of filtering and carrier detection.
In stock
+ −
Add to wish list
ARD-PROMINI-3.3V Arduino Pro Mini ATmega328P-AU 3.3V Micro controller at 8Mhz
US$10.32
The 3.3V Arduino Pro Mini Micro controller is based on the ATmega328P-AU chip set and runs at 8 Mhz. It comes with two 12 pin headers and one 6 pin
angled connector for header based connections, some soldering is required.
In stock
+ −
Add to wish list
ARD-PROMINI-5V Arduino Pro Mini ATmega328P 5v Micro controller at 16Mhz
US$17.06
The 5V Arduino Pro Mini Micro controller is based on the ATmega328P chipset and runs at 16 MHz. It comes with two 12 pin headers and one 6 pin
angled connector for header based connections, some soldering is required.
In stock
+ −
Add to wish list
Arduino Pro
ARD-PROMICRO-5V Micro Atmega32U4 5V/16MHz Arduino Module Board
US$13.93
The Pro Micro - 5V/16MHz- is similar to the Pro Mini except with an ATmega32U4 on board.
In stock
+ −
Add to wish list
2755-POLOLU Dual MC33926 Motor Driver for Raspberry Pi (Partial Kit)
US$124.42
This add-on board enables a Raspberry Pi B+, A+, or Pi 2 to drive a pair of brushed DC motors. Its dual MC33926 motor drivers operate from 5 V to 28 V and can deliver a continuous 3 A (5 A peak) per motor.
In stock
+ −
Add to wish list
WIFI-ESP8266 WiFi Serial Transceiver Wireless Module w/ ESP8266 ESP-01- 1MB Flash
US$6.96
The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The ESP8266 is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor.
In stock
+ −
Add to wish list
DEV-13630 SparkFun Photon Weather Shield
US$46.13
The SparkFun Photon Weather Shield is an easy to use add-on board that grants you access to barometric pressure, relative humidity, and temperature. There are also connections on this shield to optional sensors such as wind speed, direction, rain gauge and soil readings!
In stock
+ −
Add to wish list
DEV-13626 SparkFun Photon Battery Shield
US$22.74
The SparkFun Photon Battery Shield provides you with an easy way to power your Photon module with a Lithium polymer battery. Not only can the Battery Shield power you Photon but you will also be able to charge a LiPo bettery through it as well.
In stock
+ −
Add to wish list
DEV-13629 SparkFun Photon IMU Shield
US$36.33
This is the SparkFun Photon IMU Shield, a versatile motion-sensing add-on board for your Photon device. Each IMU shield is equipped with an on-board LSM9DS1 system-in-a-chip that houses a 3-axis accelerometer, 3-axis gyroscope, and 3-axis magnetometer. That’s right, 9 degrees of freedom (9DOF) from a single IC!
In stock
+ −
Add to wish list
DEV-13628 SparkFun Photon Micro OLED Shield
US$32.13
The SparkFun Photon Micro OLED Shield breaks out a small monochrome, blue-on-black OLED to use with your Photon module. It’s “micro”, but it still packs a punch – the OLED display is crisp, and you can fit a deceivingly large amount of graphics on there.
In stock
+ −
Add to wish list
DEV-13598 SparkFun Photon ProtoShield
US$3.50
This ProtoShield mates easily with your Photon module and provides a small soldering area and separated power and I2C hook-ups. With the SparkFun Photon ProtoShield you have the control over what kind of project you design for your Photon.
In stock
+ −
Add to wish list
DEV-13328 SparkFun Photon Wearable Shield
US$6.93
The SparkFun Photon Wearable Shield makes it easy to add the WiFi enabled Photon to any wearables project. Each pin on the Photon is broken out into large sewing pins. Use conductive thread to make your next wearables projects. The large pins are also great for using conductive paint to create any project that needs WiFi.
In stock
+ −
Add to wish list
1457187018 Make: Getting Started with the Photon: Making Things with the Affordable, Compact, Hackable WiFi Module (Paperback)
US$27.99
While the Photon--and its accompanying cloud platform--is designed as a ready-to-go foundation for product developers and manufacturers, it's great for Maker projects, as you'll see in this book. You'll learn how to get started with the free development tools, deploy your sketches over WiFi, and build electronic projects that take advantage of the Photon's processing power, cloud platform, and input/output pins.
In stock
+ −
Add to wish list
101 - 115
109 110 111 112 113 114 115 116 117 118 119 120 121 122 123
117 - 131