Development Boards

US$26.53
The ULINK2 Debug Adapter connects your PC's USB port to your target system (via JTAG, SWD, or OCDS) and allows you to program and debug embedded programs on target hardware. ULINK2 Features: Supports various ARM7, ARM9, Cortex-M4, 8051, MKD5.0 and C166 devices. JTAG speed up to 10MHz. Serial Wire Debug (SWD) support for ARM Cortex-M based devices. Serial Wire Viewer (SWV) Data Trace for Cortex-M up to 1Mbit/s (UART mode). NXP 2-wire debug interface (P89LPC952 and P89LPC954) support. With memory R/W during execution, terminal emulation, and serial debug output. Seamless integration with the Keil IDE & Debugger. Wide target voltage range: 2.7V - 5.5V. USB powered (no power supply required) Plug-and- Play installation using. Target: 10-pin (0.05") - Cortex Debug Connector, 20-pin (0.10") - ARM Standard JTAG Connector.
Delivery within 2-3 weeks
+
Add to wish list

US$4.61
This is a simple breakout board that features five pushbuttons. You can program your code to specific functions when the buttons are pressed. This board is a perfect example of how to design a circuit using only one analog pin from your microcontroller! Depending on which push button you press it will vary the voltage begin returned back to the microcontroller! If you are looking for a simple board that doesn’t use multiple digital pins and is easy to use, this board is a genius little trick to save those precious digital pins. Note: The pushbuttons come with a yellow cap, you can purchase our pushbutton kit that comes with various colored caps if you choose to decorate the board. When no buttons are pressed analogRead will indicate the full voltage 1023. SW1 will be 0, SW2 will be 30, SW3 will be 86, SW4 will be 164 and SW5 will be 348.
In stock
+
Add to wish list

US$1.39
This device is a DC power supply breakout board with a 2.1mm jack on the connector. PCB Size: 2.8 X 1.3cm. Power output interface: 2 way VCC and GROUND.
Delivery within 2-3 weeks
+
Add to wish list

US$3.84
This device is a DB9 female RS232 to 9 Position Screw Terminal Block breakout board. The wire range of the 9 Positions Screw Terminal Block is 22-14AWG. Specifications: Terminal block pitch: 3.96mm. Screw hole diameter: 2mm (use slotted screwdriver). Dimensions: Approx. 3.5cm (L) * 3cm(W) * 1cm(H). Weight: 15g.
In stock
+
Add to wish list

US$3.84
This device is a DB9 male adapter RS232 to 9 Position Screw Terminal Block breakout board. The wire range of the 9 Positions Screw Terminal Block is 22-14AWG. Specifications: Terminal block pitch: 3.96mm. Screw hole diameter: 2mm (use slotted screwdriver). Dimensions: Approx. 3.5cm (L) * 3cm(W) * 1cm(H). Weight: 15g.
In stock
+
Add to wish list

US$100.00
Ever want to build your own weather station? This anemometer is made of shell, wind cups and circuit module. It has built-in photovoltaic module, industrial microcomputer processor, and standard current generator. Made with aluminium alloy, the anemomter is of high strength, weather resistance and corrosion resistance. The millitary quality interface ensures long life of this anemometer, at the same time enhancing the accuracy of wind speed acquisition. Together with other components, this anemometer can be widely used in measureing wind in areas such as engineering, railways, docks, power plants, meteorological, cableway, environment study, agriculture, energy monitoring, health study with corresponding signal output. With the instructions and sample code, users can easily get wind speed level through voltage signal output (0 to 5v).
In stock
+
Add to wish list

US$16.00
micro:bit is a pocket-sized microcontroller designed for kids and beginners to learn coding and electronics, letting them easily bring ideas into DIY digital games, interactive projects and robotics.
In stock
+
Add to wish list

US$19.95
DFRobot FireBeetle is a series of low-power-consumption development hardware designed for Internet of Things (IoT). Firebeetle ESP8266 is a development board integrated with IoT WiFi, TCP/IP, 32-bit MCU, 10-bit ADC and multiple interfaces such as HSPI, UART, PWM, I2C and I2S. In DTIM10, the full power consumption to maintain WiFi connection reached to 1.2mW. Equipped with 16MB outer SPI flash memory, ESP8266 is available for programs and firmware storage. Compatible with Arduino programming enables Firebeetle ESP8266 to lower the barrier of programming. Operator can implement Arduino programming codes directly onto ESP8266 to reduce the difficulty of operating and increase the stability of board.
In stock
+
Add to wish list

US$8.46
This is an LED RGB ring for the WEMOS D1 Mini. The ring offers 12 RGB LEDs that can be programmed for the ESP8266 using the Adafruit Neopixel library.
In stock
+
Add to wish list

US$17.50
This Raspberry Pi Hat allows you to connect a VGA monitor to your project. Combined with your Raspberry Pi HDMI port, you can easily use 2 or more monitor screens.
In stock
+
Add to wish list

US$79.98
So you want to make and play your own games? Well micro:bit and ABRA electronics have created the perfect solution for you! The Microbit-Arcade is the only classic arcade that runs on 2 AA batteries. This kit provides all the necessary parts and instructions to have your arcade set up and running in a few hours. The buttons and joystick provide that genuine arcade feeling. The kit comes with 3 sample games (Tag, Catch and Chase) and guidelines to development your own games even further. In no time, you’ll be developing your own awesome games to show off with!
In stock
+
Add to wish list

US$11.19
This TDA7297 compact dual channel amplifier board provides 15 clean watts of audio per channel from 20 to 20,000 cycles. Amplifier runs on a wide range of DC power input from 6-18 VDC. Has a volume control potentiometer on board. Amplifier chip includes short circuit as well as thermal overload protection.
In stock
+
Add to wish list

US$8.95
The MI:pro is a simple and compact protective case for the micro:bit. These cases feature a three-layer construction style with ability to wall-mount the whole assembly onto any surface you want while still providing access to all buttons and ports on the micro:bit. Though these cases do feature wall-mountable tabs, the biggest benefit of using a case is to not accidentally short out the pads on the back of the micro:bit.
In stock
+
Add to wish list

US$13.93
The Arduino Nano I/O Sensor Shield acts as an expansion board for the Arduino Nano and DFRduino Nano microcontrollers. There are several different options for power input. The form factor of the Nano I/O Shield board is the same as the Arduino UNO/arduino Leonardo. In addition, the sensor shield adopts Gravity interface that each pinout includes 5V and GND pins for easy connection to Gravity sensors or servos. To the best compatibility, the shield supports jumper wires for rapid prototyping. This unit comes fully assembled. The board also has a space specifically for the DFRobot bluetooth module and ACP220. Several I2C pins are also expanded. The arduino nano shield has independent power supply to provide extra power for servo and other sensors.
In stock
+
Add to wish list

US$7.00
At sometime or another you may run out of pins on your Arduino board and need to extend it with shift registers. With this shift out module which is based on 74HC595. The datasheet refers to the 74HC595 as an "8-bit serial-in, serial or parallel-out shift register with output latches; 3-state." In other words, you can use it to control 8 outputs at a time while only taking up a few pins on your microcontroller. You can link multiple registers together to extend your output even more. It can also be applies to 51, AVR, PIC and other microcontroller. It is ideal to work together with Interface Shield for Arduino (DFR0074).
In stock
+
Add to wish list