Our Brands

Development Boards

71 - 85
79 80 81 82 83 84 85 86 87 88 89 90 91 92 93
87 - 101
Newest Items First
15 Per Page
OnOff SHIM
US$10.95
Our SHIMs (Shove Hardware in the Middle) are a new range of boards designed to be small, affordable, and handy. They're just 0.8mm thick (the bare board, not including mounted components) and designed to be soldered straight onto the GPIO pins of your Pi, if you wish, so that you can use them with HATs and pHATs on top.
Delivery within 2-3 weeks
+ −
Add to wish list
PIM301 Button SHIM
US$8.53
Button SHIM gives you five handy, physical buttons and an RGB status LED, and it's HAT and pHAT-compatible! Our SHIM-format boards are designed to slip neatly onto your Pi's GPIO pins and still allow you to use HATs and pHATs at the same time. Or solder the included female header onto Button SHIM and use it as a standalone board. The buttons and status LED stick out from the top edge of your Pi, making them easy to access.
In stock
+ −
Add to wish list
MNK00061 Relay for micro:bit
US$14.20
The MonkMakes Relay for micro:bit is a solid-state (no moving parts) relay that allows an output of a micro:bit to turn things on and off. A micro:bit can turn an LED on and off directly, but anything more powerful requires something like a relay or a transistor. Using a transistor to switch something on and off requires a shared ground connection with the micro:bit and a knowledge electronics that you or your students may not be ready for. The MonkMakes Relay for micro:bit is much easier to use, acting like a simple micro:bit controlled switch. This relay can be used to switch low voltage devices such as light bulbs, a motor, a small heating element or even a string of 12V LED lighting. The voltage needs to be kept under 16V, but the relay will automatically protect itself against too much current.
In stock
+ −
Add to wish list
MNK00060 Speaker for micro:bit
US$15.62
The MonkMakes Speaker for micro:bit is a neat little amplified speaker that connects to your micro:bit using alligator clips. Features: Amplified output. LED ‘power on’ indicator. Reverse polarity protection.
In stock
+ −
Add to wish list
ARD-LP-12 LilyPad ATtiny85 Development Board
US$16.96
The LilyTiny is a tiny little LilyPad board designed to add flashy functionality to your project without taking up a lot of room. Even though it’s as small as some of the LilyPad sensors, this board actually has an ATtiny microcontroller on it so it’s actually pretty powerful for its small size! 
In stock
+ −
Add to wish list
ARD-LP-RGB RGB LED Module for Arduino LilyPad
US$2.50
LilyPad Arduino is about making technology wearable. This particular module offers you a Tri-Color LED on a sewable board that you can attach onto your favourite clothing.
In stock
+ −
Add to wish list
ARD-LP-BUZ LilyPad I/O Buzzer
US$3.28
LilyPad I/O Buzzer This is a small buzzer for the LilyPad system. It uses two I/O pins on the LilyPad main board to create different noises based on the...
In stock
+ −
Add to wish list
SENS-120 FPM10A Fingerprint Reader Sensor for Microcontrollers
US$19.95
Fingerprint scanners are awesome! Why use a key when you have one right at the tip of your finger? Secure your project with biometrics - this all-in-one optical fingerprint sensor will make adding fingerprint detection and verification super simple. These modules are typically used in safes or any security system that requires fingerprint reading.
In stock
+ −
Add to wish list
MNK00064 RGB LED for micro:bit
US$5.68
The MonkMakes RGB LED for micro:bit provides a colourful add-on to your micro:bit. Connect it up with alligator clips and then use the three outputs of your micro:bit to control the red, green and blue channels to mix up any colour of light you want.
In stock
+ −
Add to wish list
Sensor for micro:bit
US$15.95
The MonkMakes Sensor Board for micro:bit allows you to sense sound level, temperature and light level. Features: 3V and GND connections can be made from either side and allow you to power a second board such as the MonkMakes Relay Board or MonkMakes Speaker. LED ‘power on’ indicator. Reverse polarity protection. All three sensors are analog and can be connected to pins P0, P1 and P2 using alligator clips.
In stock
+ −
Add to wish list
EF08183 ElecFreaks Micro:bit Tinker Kit (without Micro:bit Board)
US$69.94
ElecFreaks Micro:bit Tinker Kit (Without Micro:bit Board) is a set of accessory for micro:bit, which enables you to connect all kinds of modules easily without a group of messy breadboard wires.
In stock
+ −
Add to wish list
EF02053 ELECFREAKS Basic:bit for micro:bit three way I/O expansion, mini version
US$5.59
Basic:bit is a basic breakout board of micro:bit. It carries a buzzer and three groups of GVS pins(P0/P1/P2) on board. Each group of GVS pins separately leads out the IO port, 3V port and GND port on micro:bit. Small size with simple structure, it is quite enough for you to complete 98% micro:bit projects.
In stock
+ −
Add to wish list
EF03414 Elecfreaks edge:bit for micro:bit(edgebit)
US$6.01
Edge:bit is a breakout board for protecting your micro:bit golden finger. The special designed golden finger brings more convenience to micro:bit extension. But, at the same time, it is easily abraised or scratched by aligator clip. Edge:bit can provide an all-around protection for your micro:bit, which makes your micro:bit life span become much longer.
In stock
+ −
Add to wish list
ARD-MP3 Audio Shield For Arduino with Microphone Input and microSD Card Reader
US$15.32

Based on VS1053B from VLSI, this MP3 shiled allows you to plug into any Arduino UNO or MEGA direcly without the hassle of having a bunch of wires everywhere. It's small and convienient which makes it more easy to play music compared with the tiny mp3 breakout boards.
It includes a VS1053 chip is a versatile MP3 codec processor that is capable of decoding a variety of music formats,including Ogg/Vorbis/MP3/AAC/WMA/MIDI audio etc..For the best headphone listening experience, the VS1053 includes EarSpeaker spatial processing which accurately simulates how a room with stereo loudspeakers would sound.

 
With the TF card slot on the other side of the board, you can play mp3 files from a Micro SD card using this board.
It is easily to drop it in your project or make a mp3 player using your microcontroller.
In stock
+ −
Add to wish list
WAVE-3947 Micro SD(TF) Storage Board
US$6.01
Features: Micro SD card slot, Supports SDIO and SPI interfaces, 2.54mm pitch pinheaders.
In stock
+ −
Add to wish list
71 - 85
79 80 81 82 83 84 85 86 87 88 89 90 91 92 93
87 - 101