Our Brands

Development Boards

105 - 119
113 114 115 116 117 118 119 120 121 122 123 124 125 126 127
121 - 135
Newest Items First
15 Per Page
2196-ADA The Raspberry Leaf for Model B+ (Two Pack)
US$4.13
The Raspberry Leaf is a piece of high quality glossy paper that's cut and drilled to to pop over the GPIO pins of your Raspberry Pi B+ and label them for easy connection.
Delivery within 2-3 weeks
+ −
Add to wish list
MR001-004.2 DC Dual Motor Driver 30V 4A V2
US$17.97
This allows to indipendently drive two DC motors, controlling both velocity and direction.
In stock
+ −
Add to wish list
LAB-13110 SparkFun Inventor's Kit Parts Refill Pack
US$34.93

Kit Includes: 5x Mini Photocell, 5x 10k Trimpot, 2x Gear Hobby Motor, 2x Generic Servo (Sub-Micro Size), 2x Bag of 25 10kOhm Resistor, 2x Bag of 25 330Ohm Resistor, 5x 30 Pack of Jumper Wires, 10x 1N4148 Diode, 1x Assorted LED (20 Pack) - (5 Red, 5 Blue, 5 Yellow, 5 Green). 1x Simon Buttons (4 Pack) - (1 Red, 1 Blue, 1 Yellow, 1 Green).

In stock
+ −
Add to wish list
DEV-12935 FTDI SmartBasic
US$39.13
The FTDI SmartBasic is a variation on our classic FTDI Basic board which allows you to connect a second device to the hardware serial port on an Arduino Pro, Pro Mini, or other USB-less board without compromising the ability to bootload code from the Arduino IDE.
In stock
+ −
Add to wish list
2130-ADA Mono 2.5W Class D Audio Amplifier - PAM8302
US$16.35
This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC.
In stock
+ −
Add to wish list
2029-ADA Assembled Pi Cobbler Plus - Breakout Cable - for Pi B+/A+/Pi 2/Pi 3
US$12.17
It's an add on prototyping Pi Cobbler from Adafruit specifically designed for the B+ and Pi 2 that you can break out all those tasty power, GPIO, I2C and SPI pins from the 40-pin header onto a solderless breadboard. This will make "cobbling together" prototypes with the Pi super easy.
In stock
+ −
Add to wish list
2028-ADA Assembled Pi T-Cobbler Plus - GPIO Breakout - for RasPi A+/B+/Pi 2/Pi 3
US$12.25
The T-Cobbler Plus is an add on prototyping board from Adafruit specifically designed for the B+, Pi 2 and Pi 3 that can break out all those tasty power, GPIO, I2C and SPI pins from the 40-pin header onto a solderless breadboard. This set will make "cobbling together" prototypes with the Pi super easy.
In stock
+ −
Add to wish list
L3GD20H Triple-Axis Gyro Breakout Board - L3GD20/L3G4200 Upgrade
US$19.25
A gyroscope is a type of sensor that can sense twisting and turning motions. Often paired with an accelerometer, you can use these to do 3D motion capture and inertial measurement.
Delivery within 2-3 weeks
+ −
Add to wish list
PRT-13054 Raspberry Pi B+ - GPIO Shrouded Header (2x20)
US$1.64
This 2x20 shrouded header has the same number and spacing of pins as the Raspberry Pi B+ so you can easily connect via ribbon cable to the low-level peripherals and get hacking! This through-hole header has 40 0.1"-spaced pins and is keyed for polarity.
In stock
+ −
Add to wish list
BOB-12052 LTC4150 Coulomb Counter Breakout
US$26.55
This breakout is capable of constantly monitoring the current your sensor is using, is able to add it up, and will give you a pulse each time a given amount of amp-hours have been used. When used effectively and if you start with a full battery, you’ll always know exactly how much of it is left!
In stock
+ −
Add to wish list
VEL-VMA04 ETHERNET SHIELD FOR ARDUINO®, WPSH04
US$55.93
Configure your Arduino as a simple web server or let it get data from the worldwide web. Also available in kit version VEL-KA04.
Delivery within 2-3 weeks
+ −
Add to wish list
VEL-VMA05 I/O SHIELD FOR ARDUINO, WPSH05
US$55.93
This is a general purpose INPUT - OUTPUT shield for Arduino. Also available in kit version VEL-KA05.
Delivery within 2-3 weeks
+ −
Add to wish list
VEL-VMA02 AUDIO SHIELD FOR ARDUINO, WPSH02
US$40.25
Record your voice via a built-in microphone or a line input. Also available in kit version VEL-KA02.
Delivery within 2-3 weeks
+ −
Add to wish list
2094-ADA JTAG (2x10 2.54mm) to SWD (2x5 1.27mm) Cable Adapter Board
US$8.67
This adapter board is designed for adapting a 'classic' 2x10 (0.1"/2.54mm pitch) JTAG cable to a slimmer 2x5 (0.05"/1.27mm pitch) SWD Cable.  It's helpful for using products like theJTAGulator or SEGGER J-Link with tiny boards that use the 10-pin SWD programming connector.
In stock
+ −
Add to wish list
DEV-13035 Intel® Edison Block - OLED
US$34.93
Equip your Edison with a graphic display using the Edison OLED Block! Simply snap this board onto your Edison to gain access to a 0.66", 64x48 pixel monochrome OLED. To add some control over your Edison and the OLED, this board also includes a small joystick and a pair of push-buttons which can be used them to create a game, file navigator, or more!
In stock
+ −
Add to wish list
105 - 119
113 114 115 116 117 118 119 120 121 122 123 124 125 126 127
121 - 135