Our Brands

Sensors Current

1 2
Sort by Price: Low to High
16 Per Page
MOD-HMCT103C HMCT103C 5A/5MA Micro Current Transformer
US$3.07
This is a precision AC current transformer. It is widely used in applications such as sensing overload current, ground fault detection, metering, analog to digital circuits.
In stock
+ −
Add to wish list
MOD-MAX471-GY 3A Rated Current Sensor for Arduino Microcontrollers
US$3.84
Do you have a project that requires current sensing, running off a battery and want to know how much mAh battery pack you want to order? This product will essentially help inform you of your current consumption to whatever device you interface with this board with. This product uses a MAX471 Op-Amp to detect current, the MAX471 has an internal 35mΩ current-sense resistor and measures battery currents up to ±3A. This device typically operates from 3V to 36V, and draws less than 100µA while idle. The module is also supplied with 2 screw terminal and 0.1" pitch headers (requires soldering).
In stock
+ −
Add to wish list
MOD-MAX471 MAX471 3A Current Range Sensor Module
US$4.93
The following module allows you to measure the current of a circuit by outputting an analog value you can then send to a microcontroller board (Arduino). Connect your inputs appropriately and for every amp measured, the board will output a volt (ratio is 1V/A, max of 3 A). To get the module working, you must first connect the RS+ pin to your positive supply line, your RS- to your loads positive end and GND to a common ground plain (as if you were connecting an ammeter). Now for the output terminals, simply connect the pin labeled OUT to any analog pin on your microcontroller and the GND pin to your microcontrollers ground.
In stock
+ −
Add to wish list
SEN0223 Gravity: Conductivity Sensor Switch - DFRobot
US$6.23
The Gravity Conductivity Sensor Switch module can be used to detect if an object has electrical conductivity. Its maximum detection value is 10MΩ. It can detect not only coins, wires, metal and other good conductors, but also the human body, fruit, plants and other conductors. By touching the positive and negative terminals of the conductive switch, you can change the output state of the module. Use this to make interactive applications such as fruit pianos, musical wind chimes or interactive video game controllers so Super Mario using a bunch of bananas.
In stock
+ −
Add to wish list
AM-112 Current Sensor Module using the Hall Effect 30 Amp
US$6.93
This component allows users to measure current of their circuit and will send data to the Arduino microcontroller to spit out an analog output value. This device has only three wires required to successfully interface with Arduino. Connect VCC to 5v, gnd to ground and Out to any analog pin on the Arduino. The conversion of the pin value is per 185mv/A. We have attached an Arduino code example to get it working straight out of the package.
In stock
+ −
Add to wish list
AM-111 Current Sensor Module using the Hall Effect 20 Amp
US$7.32
This component allows users to measure current of their circuit and will send data to the Arduino microcontroller to spit out an analog output value. This device has only three wires required to successfully interface with Arduino. Connect VCC to 5v, gnd to ground and Out to any analog pin on the Arduino. The conversion of the pin value is per 185mv/A. We have attached an Arduino code example to get it working straight out of the package. Connect the return ground line of the load to the terminal block and the other input of the block to your power source like an ammeter to start reading current. This unit is designed to read a max of 20 amps!
In stock
+ −
Add to wish list
AM-110 Current Sensor Module using the Hall Effect 5 Amp
US$7.96
This component allows users to measure current of their circuit and will send data to the Arduino microcontroller to spit out an analog output value. This device has only three wires required to successfully interface with Arduino. Connect VCC to 5v, gnd to ground and Out to any analog pin on the Arduino. The conversion of the pin value is per 185mv/A. We have attached an Arduino code example to get it working straight out of the package.
In stock
+ −
Add to wish list
MOD-MAX471-4 MAX471 3A Current and Voltage Range Sensor Module
US$7.96
The MAX471 measures both current and voltage, thus making it ideal for a quick power measurement.
In stock
+ −
Add to wish list
AM-109, 30A Current Range Hall Current Sensor Module 5V
US$9.76

This device is a 30 ampere 5 volt range current Hall Sensor module.

In stock
+ −
Add to wish list
IM120710018 ELECTRONIC BRICK - ELECTRICITY METER(ANALOG)
IM120710018 ELECTRONIC BRICK - ELECTRICITY METER(ANALOG)
US$9.79
Electronic brick of electricity sensor is based on TA12-100 current transformer, which can transform AC signals of large current into small amplitude signals. The maximum current that can be detected can reach 5A, and the present current signal can be read via analog I / O port.
In stock
+ −
Add to wish list
BB-INA219 I2C Interface – DC Current Sensor (INA219)
US$10.70
This breakout board will solve all your power-monitoring problems. Instead of struggling with two multimeters, you can just use the handy INA219B chip on this breakout to both measure both the high side voltage and DC current draw over I2C with 1% precision. With the internal 12 bit ADC (Analog-Digital Converter), the resolution at ±3.2A range is 0.8mA. With the internal gain set at the minimum of div8, the max current is ±400mA and the resolution is 0.1mA.
In stock
+ −
Add to wish list
SCT-013-000 Non-invasive AC Current Sensor (100A max)
US$15.33
Specifications: Input Current: 0~100A AC. Output Mode: 0~50mA. Non-linearity: ±3%. Turn Ratio: 100A:0.05A. Resistance Grade: Grade B. Work Temperature: -25°C ~ ﹢70°C. Dielectric Strength(between shell and output): 1000V AC/1min 5mA. Leading Wire in Length: 1m. Open Size: 13mm x 13mm.
In stock
+ −
Add to wish list
SCT-013-030 Non-invasive AC Current Sensor (30A max)
US$15.33
The split core type such as this CT, is particularly suitable for DIY use it can be clipped straight on to either the live or neutral wire coming into the building without having to do any high voltage electrical work.
In stock
+ −
Add to wish list
Adafruit INA260 High or Low Side Voltage, Current, Power Sensor
US$16.15
This breakout board may well be the last current sensing solution you ever need to buy. Not only can it do the work of two multimeters, but it can do it with amazing precision and flexibility. With it you can measure high or low side DC current, the bus voltage, and have it automatically calculate the power. It can do so over impressive voltage, current, and temperature ranges with better than 1% accuracy, all while delivering the data in an easy to use format over I2C.
Delivery within 2-3 weeks
+ −
Add to wish list
SEN-11005 Non-Invasive Current Sensor - 30A
US$16.73
This particular current sensor will measure a load up to 30 Amps which makes it great for building your own energy monitor to keep your power usage down, or even building an over-current protection device for an AC load.
In stock
+ −
Add to wish list
FIT0850, NPN to PNP Signal Converter / Adapter Module
US$17.50
The FIT0850 is a signal converter designed to take NPN signals to PNP. It's equipped with surge absorption and over-current protection to further protect your device.
Delivery within 2-3 weeks
+ −
Add to wish list
1 2