Our Brands

Development Boards

84 - 98
92 93 94 95 96 97 98 99 100 101 102 103 104 105 106
100 - 114
Newest Items First
15 Per Page
3342-ADA 2x40 Right Angle Edge Connector for micro:bit
US$6.92
This is a connector that fits directly to the edge contacts of a BBC micro:bit. The connector has 80 pins, but because of the different widths of the micro:bit edge contacts, some of the micro:bit contacts will map to more than one of this connector's pins. Also, the back half of the pins are not used at all. The edge connector gives access to all the important pins on the bottom edge of the micro:bit. Check the datasheet for the pin spacing and orientation. This connector is best used with a custom PCB!
In stock
+ −
Add to wish list
ARD-FTDI-IO FTDI-232RL – USB to Serial Communication for 5v or 3.3v Microcontrollers
US$9.73
This unit is based on a genuine FTDI FT232RL chipset, we highly recommend this product for those finicky electronic speed controllers that required this chipset for programming. It can also work for devices that operate on TTL communicate and offer a way to communicate to your PC via Tera Term or Putty.
In stock
+ −
Add to wish list
BOB-16446 SparkFun micro:bit Breakout (with Headers)
US$10.46
The SparkFun micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pins and allowing for connections to the I2C and SPI buses.
In stock
+ −
Add to wish list
WEMOS-BM180 BMP180 Digital Barometric Pressure Sensor for WEMOS
US$10.00
This shield is designed for the WEMOS Mini/Mini Pro D1 and allows for precise measuring of atmospheric pressure and can be connected over WiFi. This shield uses the Bosch BMP180 to measure barometric pressure and temperature from an I2C 3.3V WEMOS Microcontroller. Combined with a WEMOS board, this information can be communicated via internet and be used to control a system. The programs are compiled using WEMOS XI expansion in Arduino.
In stock
+ −
Add to wish list
WEMOS-SD Micro-SD Shield Module for WEMOS
US$7.61
This shield allows for reading and writing to an Micro SD (TF) from the WEMOS microncontroller with access to WiFi. With this very practical tool, you can now upload and download photos and information to and from an SD from the internet. The Micro SD card slot is convenient to use with all the required pins easily connected. The programs are compiled using WEMOS XI expansion in Arduino.
In stock
+ −
Add to wish list
WEMOS-RGB RGB LED WS2812 Module Shield for WEMOS
US$6.92
This a WiFi connected WEMOS Shield for controlling an LED. This simple gadget allows you to create your very own LED show over the internet. The RGB LED let you program using different colors and timings. The programs are compiled using WEMOS XI expansion in Arduino.
In stock
+ −
Add to wish list
WEMOS-RM-1 1-Channel 5V Relay Shield Interface for WEMOS
US$6.92
This relay board allows the control of higher voltage devices such as motors and lights without any risk of damage to the controller. This particular JQC-3FF-S-Z relay has specifications that make it perfect for use with low voltage controllers such as the WEMOS. The shield package makes connection and testing even easier. Combined with a WEMOS board, this information can be communicated via internet and be used to control a system. The programs are compiled using WEMOS XI expansion in Arduino.
In stock
+ −
Add to wish list
WEMOS-DS18B20 DS18B20 Temperature Sensor Module for WEMOS
US$8.46
This small stackable type shield is powered by the very precise wide range DS18B20 digital temperature sensors and allows to obtain readings. Combined with a WEMOS board, this information can be communicated via internet and be used to control a system.
In stock
+ −
Add to wish list
WEMOS-MINI-PRO Wemos D1 Mini Pro – IoT Development Board
US$16.86
The Wemos D1 mini Pro is a mini wifi board based on ESP-8266EX microcontroller. This multi-purpose board is a fully functional microcontroller (SCL, SDA, SCK, MISO, MOSI, TX, RX, Reset) with the added fonctionality of connecting to a wifi network. Thus, allowing you to create a full range of IoT projects and gadgets. The board runs off the very powerful Espressif chip set with an on-board ceramic antenna and a dock for connecting another for better reception. The board runs at a 3.3V logic level but offers a 5V power pin.
In stock
+ −
Add to wish list
WEMOS-DHT11 DHT11 Shield for WEMOS – Digital Temperature/Humidity Sensor Module
US$6.92
The WEMOS DHT11 Shield is a temperature and humidity sensor shield compatible with WEMOS Mini and Mini Pro with headers for stacking. This small stackable type shield is powered by the very common DHT11 digital temperature and humidity sensors and allows to obtain readings. Combined with a WEMOS board, this information can be communicated via internet and be used to control a system.
In stock
+ −
Add to wish list
WEMOS-DHT22 DHT22 Shield for WEMOS – Digital Temperature/Humidity Sensor Module
US$10.93
The WEMOS DHT11 Sheild is a temperature and humidity sensor shield compatible with WEMOS Mini and Mini Pro with headers for stacking. This small stackable type shield is powered by the very common DHT22 digital temperature and humidity sensors and allows to obtain readings. (The DHT22 is a much more precise and wide range sensor than its DHT11 counterpart). Combined with a WEMOS board, this information can be communicated via internet and be used to control a system.
In stock
+ −
Add to wish list
CAB-600-R USB A to Micro B Cable for micro:bit or Raspberry Pi Pico– 80cm long
US$1.39
Looking for a USB cable for your android phone, BBC-MicroBit, Arduino Promicro or any device that needs an Micro-B to USB A cable? This product can do both data transfer and supply power to your target device! It is also long enough, making programming and debugging a lot easier. Length: 80cm / 31.49 Inches / 2.62 Feet
In stock
+ −
Add to wish list
SF-FTDI232R 3.3V 5V FTDI232R USB to TTL Serial Adapter Module
US$13.85
This USB to TTL serial adapter module can work with different types of computer systems and drivers. The power LED, TXD LED and RXD LED on the module can help indicate whether it works normally. With the build-in signal voltage switch, when you switch to 5V, the power at TXD and RXD will be 5V; if you switch to 3.3V, then the power is 3.3V. Therefore, if your device can take only 3.3V input, this module is a great choice. A 500mA self-restore fuse is used for over current protection. The module can also be used for general serial applications.
Delivery within 2-3 weeks
+ −
Add to wish list
DFR0224 Screwless Terminal Shield For Arduino
US$15.00
Annoyed with finding screwdriver when connecting wires, this Screwless Terminal Shield is a new way to plug wires to a terminal. This shield features modular screwless terminal blocks which are flexible and efficient and the wires are easy to replace with no need for special tooling. It also has standard arduino pin out which allows extra shield to be stacked on top of it. With this screwless terminal shield, make a prototyping project is much easier. Easy and Quick.
In stock
+ −
Add to wish list
STM32F103C8T6 ARM STM32 Minimum System Development Board Module for Arduino
US$13.60
This is a powerful development MCU board by ARM (STM32F103C8T6) The STM32F103xx medium-density performance line family incorporates the high-performance ARM®Cortex®-M3 32-bit RISC core operating at a 72 MHz frequency, high-speed embedded memories (Flash memory up to 128 Kbytes and SRAM up to 20 Kbytes), and an extensive range of enhanced I/Os and peripherals connected to two APB buses. All devices offer two 12-bit ADCs, three general purpose 16-bit timers plus one PWM timer, as well as standard and advanced communication interfaces: up to two I2Cs and SPIs, three USARTs, an USB and a CAN.
In stock
+ −
Add to wish list
84 - 98
92 93 94 95 96 97 98 99 100 101 102 103 104 105 106
100 - 114