Our Brands

Development Boards

126 - 140
134 135 136 137 138 139 140 141 142 143 144 145 146
Newest Items First
15 Per Page
74HC595 Shift Register 8-Bit
74HC595 Shift Register 8-Bit
US$0.69

The 74HC595 is a 16 pin dip 8-bit shift register integrated circuit.

In stock
+ −
Add to wish list
A000067 Arduino Mega 2560 Rev.3
A000067 Arduino Mega 2560 Rev.3
US$71.84
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. 
In stock
+ −
Add to wish list
A000064 Arduino Wireless Proto Shield
A000064 Arduino Wireless Proto Shield
US$23.03
The module can communicate up to 100 feet indoors or 300 feet outdoors (with line-of-sight). It can be used as a serial/usb replacement or you can put it into a command mode and configure it for a variety of broadcast and mesh networking options.
In stock
+ −
Add to wish list
CAB-10087 OBD-II to DB9 Cable
CAB-10087 OBD-II to DB9 Cable
US$21.53
This is a cable that will allow you to access the pins on your car's OBDII connector. It has an OBDII connector on one end and a DB9 female serial connector on the other.  The overall length of the cable is 5'.
Delivery within 2-3 weeks
+ −
Add to wish list
CAB-10215 USB microB Cable - 6'
CAB-10215 USB microB Cable - 6'
US$5.95
This is a 6 foot USB2.0 male type A to micro USB male B cable. Works great with the Raspberry Pi or Particle Photon.
In stock
+ −
Add to wish list
COM-08033 Button Pad 4x4 - Led Compatible
COM-08033 Button Pad 4x4 - Led Compatible
US$20.19
This is a simple breakout board for the button pads. Each LED and button is brought out to the side connectors. The connectors are soldered to the back side of the PCB. We recommend trimming the connector leads on the button side as short as possible to reduce the deflection of the pad.
In stock
+ −
Add to wish list
TOL-10405 Needle Set
TOL-10405 Needle Set
US$3.50
This set of sewing needles is a must-have when stitching together your next e-textile project. Each envelope contains three 48mm, 1.23mm thick needles and two smaller 39mm, 0.67mm thick needles.
In stock
+ −
Add to wish list
RTL-10774 Touch Sensor Shield
RTL-10774 Touch Sensor Shield
US$22.33
The MPR121 IC is a great way to build simple capacitive touch interfaces, and now it's even easier to incorporate into your Arduino projects with the touch shield. The touch shield has 9 capacitive touch pads, with headers for the remaining 3 electrode connections.
In stock
+ −
Add to wish list
DEV-08822 Coin Cell Holder - Sewable SMD
DEV-08822 Coin Cell Holder - Sewable SMD
US$2.76
This is a coin cell holder for the common CR2032 type battery. The holder has a neat pop-in, pop-out feature that makes changing the battery easy. The feet of the holder have a small hole that allow it to be sewn without modification.
In stock
+ −
Add to wish list
DEV-09350 LilyPad Slide Switch
DEV-09350 LilyPad Slide Switch
US$3.31
This is a simple slide switch for the LilyPad. Use it as a simple ON/OFF switch, or to control LEDs, buzzers, sensors, etc.
In stock
+ −
Add to wish list
DEV-08777 LilyPad Temperature Sensor
DEV-08777 LilyPad Temperature Sensor
US$9.24
This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to digital conversion on the signal line will allow you to establish the local ambient temperature.
In stock
+ −
Add to wish list
DEV-08467 LilyPad Tri-Color LED
DEV-08467 LilyPad Tri-Color LED
US$8.20
Use the Tri-Color LED board as a simple indicator, or by pulsing the red, green, and blue channels, you can create any color. Very bright output.
In stock
+ −
Add to wish list
DEV-11008 LilyPad Vibe Board
DEV-11008 LilyPad Vibe Board
US$14.25

Apply 5V and be shaken by this small, but powerful vibration motor. Works great as an physical indicator without notifying anyone but the wearer.

In stock
+ −
Add to wish list
DEV-10753 LilyPad LED Micro - White (5pcs)
DEV-10753 LilyPad LED Micro - White (5pcs)
US$5.53
By eliminating the resistor and changing the orientation of the surface mount LED we've shrunk the board down which looks great in elegant designs or on sheer fabrics where you don't need the extra weight or exposed board space. It's really the closest you can come to sewing a point of light directly to your project.
In stock
+ −
Add to wish list
BOB-00495 SOIC to Dip Adapter 20-Pins
BOB-00495 SOIC to Dip Adapter 20-Pins
US$4.14

This is a breakout board made for 20 pins SOIC style. This custom PCB will interface a standard SOIC package IC to 0.1" headers, which are easier to work with and integrate well with breadboards. There is DIP-standard 0.6" spacing between the two rows of pins.

In stock
+ −
Add to wish list
126 - 140
134 135 136 137 138 139 140 141 142 143 144 145 146