Our Brands

Development Boards

125 - 139
133 134 135 136 137 138 139 140 141 142 143 144
Newest Items First
15 Per Page
BOB-09816 OpAmp Breakout
BOB-09816 OpAmp Breakout
US$11.10
This is a simple Op Amp breakout board, set up as a 2-stage amplifier with a gain of 100 (gain of 10 for each stage). The on-board trim pot sets the signal level between the stages, not the feedback path. The bandwidth is set to 15.9kHz by a pair of feedback capacitors, or over 100kHz with the caps removed.
In stock
+ −
Add to wish list
BOB-00716 Breakout Board for RJ45
BOB-00716 Breakout Board for RJ45
US$1.92
This is a small PCB that brings out the pins of the RJ45 connector to an in-line 0.1" footprint. Use with break-away headers for breadboarding or create your own RJ45 cable connection.
In stock
+ −
Add to wish list
BOB-09110 Breakout Board for Thumb Joystick
BOB-09110 Breakout Board for Thumb Joystick
US$4.10

This is a PCB for the Thumb Joystick. Pins are broken out to a 0.1" header and includes 4 mounting holes in the corners. Dimensions: 1" X 1.25"

Delivery within 2-3 weeks
+ −
Add to wish list
BOB-09118 Opto-Isolator Breakout
BOB-09118 Opto-Isolator Breakout
US$9.76
This is a board designed for opto-isolation and electrically isolates a controller from the high-power system by use of an opto-isolator IC. This board is helpful for connecting digital systems (like a 5V microcontroller) to a high-voltage or noisy system.
In stock
+ −
Add to wish list
BOB-10467 LED Tactile Button Breakout
BOB-10467 LED Tactile Button Breakout
US$3.50
This is a PCB for the LED tactile button and easy to use on your next project. Populate the board according to the polarity of the LED on the switch. The markings for the switch are irrelevant and can be reversed.
In stock
+ −
Add to wish list
27911 Gyroscope Module 3-Axis L3G4200D
27911 Gyroscope Module 3-Axis L3G4200D
US$41.99
This is a low power 3-axis angular rate sensor featuring temperature data as an added bonus. Raw angular rate and temperature data measurements are accessed from the selectable digital I2C or SPI interface.
Delivery within 2-3 weeks
+ −
Add to wish list
BOB-10402 EM-406 Connector Breakout
BOB-10402 EM-406 Connector Breakout
US$6.93
This is a simple breakout board that uses a vertical SMD connector for the EM401 or EM406 GPS module cables.
In stock
+ −
Add to wish list
BOB-00193 Adapter Board for Microchip ICD and ICD2
BOB-00193 Adapter Board for Microchip ICD and ICD2
US$6.93
This is a small PCB that adapts the standard Microchip 6-Pin RJ11 connector to the Olimex 6-Pin .1" Molex Connector.
In stock
+ −
Add to wish list
BOB-09056 Analog / Digital MUX Breakout
BOB-09056 Analog / Digital MUX Breakout CD74HC4067
US$10.17
This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067. This chip can be used to connect 16 analog sources (like sensors) to 5 pins on a microcontroller.
In stock
+ −
Add to wish list
BOB-09868 Breakout Board for ADMP401 MEMS Microphone
BOB-09868 Breakout Board for ADMP401 MEMS Microphone
US$15.33
This is a tiny breakout board and the microphone's input can fit flush against the enclosure of your project. The amplifier on the breakout has a gain of 67 and more than meets the bandwidth requirements of the mic.
In stock
+ −
Add to wish list
DEV-10508 Touch Shield
DEV-10508 Touch Shield
US$20.93

A great way to build simple capacitive touch interfaces, and now it's even easier to incorporate into your Arduino projects with the touch shield. The touch shield has 9 capacitive touch pads, with headers for the remaining 3 electrode connections. With this shield you can have a total of 12 touch sensitive buttons.

In stock
+ −
Add to wish list
DEV-09716 FTDI Basic Breakout - 5V
DEV-09716 FTDI Basic Breakout - 5V
US$26.52

This is a basic breakout board for the FTDI FT232RL USB to serial to work with official Arduino and cloned 5V Arduino boards.

In stock
+ −
Add to wish list
DEV-09717 FTDI Cable 5V VCC - 3.3V I/O
DEV-09717 FTDI Cable 5V VCC - 3.3V I/O
US$35.27

This is a FTDI cable converter which allows for a simple way to connect serial (TTL) interface devices to USB. but also configured to operate at 5V with 3.3V I/O. The FTDI cable is designed around an FT232RQ, which is housed in a USB A connector.

In stock
+ −
Add to wish list
RTL-10709 GPS Shield Kit Retail
RTL-10709 GPS Shield Kit Retail
US$111.93
This  is a package GPS Shield Kit with EM406 GPS receiver and headers included inside a a clear clamshell. Adding GPS to your Arduino has never been easier. Multiple GPS receivers attach easily to the shield, and with the example sketch, you will be able to locate your exact position within a few meters.
In stock
+ −
Add to wish list
RTL-09899 MicroSD Shield Retail
RTL-09899 MicroSD Shield Retail
US$23.73

This can equip your Arduino with mass-storage capability, so you can use it for data-logging or other related projects. All new microSD shields have a voltage converter chip on-board that converts the Arduino 5V signals to 3.3V signals in accordance with SD specifications.

In stock
+ −
Add to wish list
125 - 139
133 134 135 136 137 138 139 140 141 142 143 144