Development Boards

US$23.02
The FLORA is small (1.75" diameter, weighing 4.4 grams). The FLORA family also has the best stainless steel threads, sensors, GPS modules and chainable LED NeoPixels, perfect accessories for the FLORA main board. The FLORA has built-in USB support. Built in USB means you plug it in to program it, it just shows up - all you need is a Micro-B USB cable, no additional purchases are needed!
In stock
+
Add to wish list

US$10.71

This switching supply gives a clean regulated 5V output at up to 2000mA. 110 or 240 input. This cable terminates with a 'standard' 5.5mm OD, 2.1mm ID positive tip connector. This wall adapter is perfect for supplying power to the BeagleBone Black.

In stock
+
Add to wish list

US$17.42
This PCB fits neatly on top of a Beagle Bone, without getting in the way of the Ethernet jack, and provides a breakout to both 46 pin headers - with individual numbering to keep them straight.
In stock
+
Add to wish list

US$6.92
This is a 9V battery pack with on/off switch and a pre-attached 5.5mm/2.1mm barrel plug. Use this to battery-power your Arduino (or other electronic projects) - it's ready to go out of the box!
In stock
+
Add to wish list

US$5.25
These are high quality battery clips. They're molded plastic so they wont tear like cheap clips, and they cover the battery terminals to prevent shorts.
In stock
+
Add to wish list

US$7.00
This here is your standard A-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Arduino, USBtinyISP, or USB Boarduino (among other things).
In stock
+
Add to wish list

US$138.53
Included are plenty of parts to make a few different fun projects! There's a Flora motherboard, a GPS module that can also perform location datalogging, eight ultra-bright chainable RGB pixels, a battery holder and batteries, two types of our high quality stainless steel thread, alligator clips to help you test out your parts, a USB cable for reprogramming the Flora, and some parts to make a wearable remote control (or TV-B-Gone!): NPN transistors, long range IR LEDs, and matching resistors.
In stock
+
Add to wish list

US$15.17
This thread is 3 ply, thicker than every day polyester or cotton thread but still thin enough to be sewn by hand in medium-eye needles. This may be sew-able by a sewing machine that can handle 'heavy' thread. Because it is strong and smooth, its ideal for any wearable/e-textile project.
In stock
+
Add to wish list

US$10.86
This thread is 2 ply, a little thicker than every day polyester or cotton thread but still thin enough to be sewn by hand in medium-eye needles or with a sewing machine that can handle 'heavy' thread. Because it is strong and smooth, its ideal for any wearable/e-textile project.
In stock
+
Add to wish list

US$6.09
The small 5mm size of these tin-plated brass snaps means they fit perfectly on Flora's pads! Snaps make a great connector for wearables-- solder one side to the board and sew the other to your project with conductive thread! This card comes with 24 complete snaps (socket and stud pairs).
In stock
+
Add to wish list

US$3.01
These magnetic pin backs have two pieces: a metal bar with adhesive strip and a plastic piece with two strong rare-earth magnets. Affix the metal bar to your FLORA projects-- it's just the right size! Then attach your FLORA project to any garment without poking holes in your clothes.
Delivery within 2-3 weeks
+
Add to wish list

US$3.01
2 x #3 needles (0.04" x 1.75") (1mm x 45mm). 6 x #5 needles (0.0375" x 1.65") (0.95mm x 42mm). 8 x #7 needles (0.035" x 1.55") (0.9mm x 39mm). 4 x #9 needles (0.027" x 1.35") (0.7mm x 35mm).
In stock
+
Add to wish list

US$22.74
This provides 16-bit precision at 860 samples/second over I2C. The chip can be configured as 4 single-ended input channels, or two differential channels.
In stock
+
Add to wish list

US$25.20

After you've assembled it, simply plug the RaspiRobot Board into the GPIO port on the Raspberry Pi and it provides dual bi-directional motor controllers, two open collector outputs, two switch inputs, a pair of status LEDs and even a voltage regulator capable of powering the Pi using a battery source from 7-12VDC.

In stock
+
Add to wish list

US$43.67
This pi plate is perfect for when you want to build a stand-alone project with its own user interface. The 4 directional buttons plus select button allows basic control without having to attach a bulky computer. The plate is designed for both Revision 1 and Revision 2 Raspberry Pi's. It uses the I2C (SDA/SCL) pins. We have a special xtra-tall 26-pin header so the plate sits above the USB and Ethernet jacks.
In stock
+
Add to wish list