Our Brands

Development Boards

112 - 126
120 121 122 123 124 125 126 127 128 129 130 131 132 133 134
128 - 142
Newest Items First
15 Per Page
572 Adafruit Proto Cape Kit for Beagle Bone
572 Adafruit Proto Cape Kit for Beagle Bone
US$17.42
This PCB fits neatly on top of a Beagle Bone, without getting in the way of the Ethernet jack, and provides a breakout to both 46 pin headers - with individual numbering to keep them straight.
In stock
+ −
Add to wish list
67 9V battery holder with switch & 5.5mm/2.1mm plug
67-ADA 9-Volt battery holder and (-volt battery clip with switch & 5.5mm/2.1mm plug
US$6.92
This is a 9V battery pack with on/off switch and a pre-attached 5.5mm/2.1mm barrel plug. Use this to battery-power your Arduino (or other electronic projects) - it's ready to go out of the box!
In stock
+ −
Add to wish list
80 Battery Clip 9V with 5.5mm/2.1mm plug
80-ADA Battery Clip 9V with 5.5mm/2.1mm plug
US$5.25
These are high quality battery clips. They're molded plastic so they wont tear like cheap clips, and they cover the battery terminals to prevent shorts.
In stock
+ −
Add to wish list
62 USB Cable - Standard A-B - 3 ft/1m
62 USB Cable - Standard A-B - 3 ft/1m
US$7.00
This here is your standard A-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Arduino, USBtinyISP, or USB Boarduino (among other things).
In stock
+ −
Add to wish list
1090 FLORA GPS Starter Pack
1090 FLORA GPS Starter Pack
US$138.53
Included are plenty of parts to make a few different fun projects! There's a Flora motherboard, a GPS module that can also perform location datalogging, eight ultra-bright chainable RGB pixels, a battery holder and batteries, two types of our high quality stainless steel thread, alligator clips to help you test out your parts, a USB cable for reprogramming the Flora, and some parts to make a wearable remote control (or TV-B-Gone!): NPN transistors, long range IR LEDs, and matching resistors.
In stock
+ −
Add to wish list
641 Stainless Medium Conductive Thread - 3 ply - 18 meter/60 ft
641 Stainless Medium Conductive Thread - 3 ply - 18 meter/60 ft
US$15.17
This thread is 3 ply, thicker than every day polyester or cotton thread but still thin enough to be sewn by hand in medium-eye needles. This may be sew-able by a sewing machine that can handle 'heavy' thread. Because it is strong and smooth, its ideal for any wearable/e-textile project.
In stock
+ −
Add to wish list
640 Stainless Thin Conductive Thread - 2 ply - 23 meter/76 ft
640 Stainless Thin Conductive Thread - 2 ply - 23 meter/76 ft
US$10.86
This thread is 2 ply, a little thicker than every day polyester or cotton thread but still thin enough to be sewn by hand in medium-eye needles or with a sewing machine that can handle 'heavy' thread. Because it is strong and smooth, its ideal for any wearable/e-textile project.
In stock
+ −
Add to wish list
1126 Sewable Snaps - 5mm Diameter - Card of 24
1126 Sewable Snaps - 5mm Diameter - Card of 24
US$6.09
The small 5mm size of these tin-plated brass snaps means they fit perfectly on Flora's pads! Snaps make a great connector for wearables-- solder one side to the board and sew the other to your project with conductive thread! This card comes with 24 complete snaps (socket and stud pairs).
In stock
+ −
Add to wish list
1170 Magnetic Pin Back
1170 Magnetic Pin Back
US$3.01
These magnetic pin backs have two pieces: a metal bar with adhesive strip and a plastic piece with two strong rare-earth magnets. Affix the metal bar to your FLORA projects-- it's just the right size! Then attach your FLORA project to any garment without poking holes in your clothes.
Delivery within 2-3 weeks
+ −
Add to wish list
615 Needle set - 3/9 sizes - 20 needles
615 Needle set - 3/9 sizes - 20 needles
US$3.01
2 x #3 needles (0.04" x 1.75") (1mm x 45mm). 6 x #5 needles (0.0375" x 1.65") (0.95mm x 42mm). 8 x #7 needles (0.035" x 1.55") (0.9mm x 39mm). 4 x #9 needles (0.027" x 1.35") (0.7mm x 35mm).
In stock
+ −
Add to wish list
1085 ADS1115 16-Bit ADC - 4 Channel with Programmable Gain Amplifier
1085 ADS1115 16-Bit ADC - 4 Channel with Programmable Gain Amplifier
US$22.74
This provides 16-bit precision at 860 samples/second over I2C. The chip can be configured as 4 single-ended input channels, or two differential channels.
In stock
+ −
Add to wish list
KIT-11561 RaspiRobot Board
KIT-11561 RaspiRobot Board
US$25.20

After you've assembled it, simply plug the RaspiRobot Board into the GPIO port on the Raspberry Pi and it provides dual bi-directional motor controllers, two open collector outputs, two switch inputs, a pair of status LEDs and even a voltage regulator capable of powering the Pi using a battery source from 7-12VDC.

In stock
+ −
Add to wish list
1109 Adafruit RGB Positive 16x2 LCD+Keypad Kit for Raspberry Pi
US$43.67
This pi plate is perfect for when you want to build a stand-alone project with its own user interface. The 4 directional buttons plus select button allows basic control without having to attach a bulky computer. The plate is designed for both Revision 1 and Revision 2 Raspberry Pi's. It uses the I2C (SDA/SCL) pins. We have a special xtra-tall 26-pin header so the plate sits above the USB and Ethernet jacks.
In stock
+ −
Add to wish list
802 Adafruit 1.8" 18-bit Color TFT Shield w/microSD and Joystick
802 Adafruit 1.8" 18-bit Color TFT Shield w/microSD and Joystick
US$53.68
This lovely little shield is the best way to add a small, colorful and bright display to any project. We took our popular 1.8" TFT breakout board and remixed it into an Arduino shield complete with microSD card slot and a 5-way joystick navigation switch (with a nice plastic knob)!
In stock
+ −
Add to wish list
85-ADA Shield Stacking Headers for Arduino (R3 Compatible)
85-ADA Shield Stacking Headers for Arduino (R3 Compatible)
US$3.42
These are standard 6-pin, 8-pin and 10-pin 0.1" spacing female headers...with a twist! The pins are extra long which means you can use these to stack shields!
In stock
+ −
Add to wish list
112 - 126
120 121 122 123 124 125 126 127 128 129 130 131 132 133 134
128 - 142