Our Brands

Development Boards

98 - 112
106 107 108 109 110 111 112 113 114 115 116 117 118 119 120
114 - 128
Newest Items First
15 Per Page
T-30-R Mini Digital Voltmeter - Red
US$4.54
This device is based on Red Seven Segment Displays at the size of 0.28 inch per digit. It operates from 2.6v to 30v (max) and has two leads both negative and positive, making this very simple to integrate to your circuit. You may need to calibrate the values on the back next to the 16 pin IC using a 1mm screw.
In stock
+ −
Add to wish list
T-30-GN Mini Digital Voltmeter-Green
US$4.54
This device is based on green Seven Segment Displays at the size of 0.28 inch per digit. It operates from 2.6v to 30v (max) and has two leads both negative and positive, making this very simple to integrate to your circuit. You may need to calibrate the values on the back next to the 16 pin IC using a 1mm screw.
In stock
+ −
Add to wish list
T-40 USB Voltage/Current Meter
US$7.20
Not to fret with this USB Voltage/Current Meter, compact portable and simple plug and play device makes reading values from a USB device seem easy. Features a blue Seven Segment Display that will display over time intervals voltage and current draw.
In stock
+ −
Add to wish list
T-45 USB Power Meter
US$13.93
This device is a meter that can measure the voltage output, the mAh for the entire duration usage until reset switch is pressed and real-time current draw. It features a nice led display to show the values and has a blue see through body with back lighting.
In stock
+ −
Add to wish list
DFR0360 XSP - Arduino Programmer
US$28.75
XSP Programmer is designed for Arduino/AVR device. It is a driver free programmer, supporting Arduino/AVR ISP and FTDI programming. It could provide both 5V and 3.3V power output or self-adaption power output(OFF mode). Support Xbee socket and auto-match ISP clock frequency.
In stock
+ −
Add to wish list
DEV-12898 SparkFun MIDI Shield
US$37.41
The SparkFun MIDI Shield board gives your Arduino-based device access to the antiquated, but still widely used and well supported MIDI communication protocol, so you can control synthesizers, sequencers, and other musical devices.
In stock
+ −
Add to wish list
DEV-13262 CAN-BUS Shield
US$51.37
The CAN-BUS Shield provides your Arduino or Redboard with CAN-BUS capabilities and allows you to hack your vehicle. It uses the Microchip MCP2515 CAN controller with the MCP2551 CAN transceiver. CAN connection is via a standard 9-way sub-D for use with OBD-II cable. Ideal for automative CAN application.
In stock
+ −
Add to wish list
2743-ADA SWD (2x5 1.27mm) Cable Breakout Board
US$4.50
This adapter board is designed to make it easier to use ARM dev boards that use slimmer 2x5 (0.05"/1.27mm pitch) SWD cables for programming.
In stock
+ −
Add to wish list
ARD-SS Arduino Sensor Shield
US$9.10
This Sensor Shield for Arduino Uno compatible microcontrollers makes interfacing with sensors and servos a breeze. All digital pins have been shifted inwards from where you would usually find them and next to the Digital Pins (S) are Gnd (G) and Vcc (V) bus. You can remove the jumper near the terminal block (SEL) and supply any fixed voltage from the terminal block you want for the entire Vcc bus or keep the jumper in place and offer 5v from Arduino 5V pin.
In stock
+ −
Add to wish list
ARD-DUE Arduino Due R3 Compatible
US$81.85
The Arduino Due R3 has 54 digital input/output pins (12 can be assigned as 8-bit PWM outputs), 12 analog inputs, 4 UARTs, an 84MHz clock, USB-OTG capable connection, 2 DAC, ADC 12 bit resolution, 2 TWI, power jack, SPI header, JTAG header and a reset button.
In stock
+ −
Add to wish list
PI-100 Micro USB to DC power Adapter for Raspberry Pi
US$2.98
This little wire will let you connect one of our 5V 2Amp adapters (276-ADA) to something that expects to be connect to Micro USB. One end has a Micro USB female jack and the other end is a 'standard' 5.5mm O.D (Outer Dimension) / 2.1mm (I.D) Inner Dimension DC jack with center positive polarity. 
In stock
+ −
Add to wish list
ARD-200 RS232 to TTL Converter Interface Module
US$11.35
This product comes in handy when you are working with a computer that has RS232 ports available, instead of fumbling for precious USB I/O ports you can connect this device straight into the RS232 port.
In stock
+ −
Add to wish list
PGM-PIC-3 Pickit 3 Programmer
US$68.20
The PICkit 3 allows debugging and programming of PIC and dsPIC microcontrollers using the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE). The MPLAB PICkit 3 is connected to a PC using a full speed USB interface and can be connected to the target via an Microchip debug (RJ-11) connector (compatible with MPLAB ICD 2/ 3 and MPLAB REAL ICE).
In stock
+ −
Add to wish list
PGM-AVR-10 AVR USBtiny programmer
US$17.97
This premade board acts like a AVR programmer and uses SPI Interface. Works with avrdude (cmd) or avrdudess (GUI) and AVRStudio-compatible. You can flash firmwares using this tiny programmer or bitbang commands to avr chipsets.
In stock
+ −
Add to wish list
PGM-AVR-5 AVR USBASP Programmer
US$10.32
This programmer is based on Thomas Fischl’s USBasp design and connects your computer’s USB port to your microprocessor using SPI. This device is supported in AVRDude version 5.2 and onwards, Allows you to read/write to any atmel based microprocessors. Works in windows 7/8/10, Mac and Linux.
In stock
+ −
Add to wish list
98 - 112
106 107 108 109 110 111 112 113 114 115 116 117 118 119 120
114 - 128