Development Boards

US$10.87
The PCF8591 AD DA Board features an 8-bit A/D Converter & D/A Converter PCF8591 with four analog inputs, one analog output and a serial I2C-bus interface.
In stock
+
Add to wish list

US$6.29

Features: PL2303TA onboard (the latest device, compatible with PL2303HXA). Supports windows XP/7/8/8.1/10/... 3 power mode : 5V output, 3.3V output, or powered by target board (3.3V-5V). 3 LEDs: TXD LED, RXD LED, POWER LED.

In stock
+
Add to wish list

US$6.29

Features: PL2303TA onboard (the latest device, compatible with PL2303HXA). Supports windows XP/7/8/8.1/10/... 3 power mode : 5V output, 3.3V output, or powered by target board (3.3V-5V). 3 LEDs: TXD LED, RXD LED, POWER LED.

In stock
+
Add to wish list

US$13.93
Features: Official case for the Raspberry Pi from the Raspberry Pi Foundation. Removable Lid for easy access to the camera and display ports. Removable Side Panels with easy access to the GPIO port. Removable Top Frame. Designed with Pi HAT's in mind.
In stock
+
Add to wish list

US$7.69
Working on a project and you want to save space but have the same functionalities as an Uno? This shield allows you to work like a Arduino Uno, using the Arduino Nano microcontroller in the center. Plug additional shields to stack to or under by purchasing some headers to extend the device. Power with a 7 – 9v battery and let the regulator bring the voltage to a tolerable amount for the microcontroller to function.
In stock
+
Add to wish list

US$8.39

Features: Original FT232RL onboard. Supports Mac, Linux, Android, WinCE, Windows 7/8/8.1/10... 3 power mode : 5V output, 3.3V output, or powered by target board (3.3V-5V). 3 LEDs: TXD LED, RXD LED, POWER LED.

In stock
+
Add to wish list

US$11.78

Features: Original FT232RL onboard. Supports Mac, Linux, Android, WinCE, Windows 7/8/8.1/10... 3 power mode : 5V output, 3.3V output, or powered by target board (3.3V-5V). 3 LEDs: TXD LED, RXD LED, POWER LED.

In stock
+
Add to wish list

US$19.31
The FT232 EVAL BOARD provides a high-performance cost-effective solution for USB TO UART. It is based on the FT232RL chip and will hopefully allow to try out the full potential of the FT232 device before using it in your prototype.
In stock
+
Add to wish list

US$8.39
The CP2102 USB UART Board (type A) is an accessory board that features the single-chip USB to UART bridge CP2102 onboard.
In stock
+
Add to wish list

US$8.39
The CP2102 USB UART Board (mini) is an accessory board that features the single-chip USB to UART bridge CP2102 onboard.
In stock
+
Add to wish list

US$13.99
The CP2102 EVAL BOARD is an evaluation board designed for CP2102, integrates MAX3232/SP3232, USB connector, DB9 connector onboard.
In stock
+
Add to wish list

US$13.99

Features: Arduino standard interfaces, compatible with Arduino boards like Arduino UNO, Leonardo, NUCLEO, XNUCLEO. Rotate the potentiometer to adjust analog input signal. Onboard 12bit DAC MCP4725, outputs required wave form. Demonstrate the DAC/PWM effects via LED and speaker.

In stock
+
Add to wish list

US$25.19

Accessory Shield integrates common used accessories/components listed as follows: Joystick (5 directions), Adjustable potentiometer, Buzzer, RGB LED, Temperature sensor, 3-axis digital accelerometer, High precision RTC, 0.96inch OLED, XBee interface.

In stock
+
Add to wish list

US$6.99
The 8 SEG LED Board enables you to easily add four 8-segment digits to your device. It is ideal for applications such as displaying the digits and/or time.
In stock
+
Add to wish list

US$4.19
The Waveshare 3678 8 Push Buttons module provides 8 single push buttons in a small board.
In stock
+
Add to wish list