Opto/Illumination

US$0.99

These are 5mm diffused RGB LEDs with only two pins that will slowly change color when voltage and ground is applied.

In stock
+
Add to wish list

US$1.06
This is a T3¼ lamp socket E10 holder bayonet style.  
In stock
+
Add to wish list

US$0.83
This is a T3¼ lamp socket holder E10 screw style.  
In stock
+
Add to wish list

US$29.67
These LED's use about 9.5 Watts max (~2 Amps @ 5V) per meter. The max rating is assuming all the LEDs are on full white, usually the actual current for colorful design is about 1/3 to 1/2 the max current. A good power supply such as our 5V 2A or 10A supply is key!
In stock
+
Add to wish list

US$0.97
These LED holders accept a 10mm LED and mount into an 35/64" diameter hole.
In stock
+
Add to wish list

US$0.97
These plastic LED holders have a black finish and only need the LED and the holder to be snapped into place easily and effectively, no screwing anything into place. These LED holders accept a 5mm LED and mount into an 19/64" diameter hole.
In stock
+
Add to wish list

US$10.42
Made of 3mm black acrylic pieces, with 4 x 1" nylon screws & 4 x nylon hex nuts, it goes together in a jiffy and looks super-spiffy!
Delivery within 2-3 weeks
+
Add to wish list

US$26.53
This is a USB to RS-232 bridge converter which is very small and easy to use. It uses a mini-B type USB connector to connect to your PC and is based on the FTDI FT232RQ USB to Serial Bridge IC from FTDI. The μUSB-PA5 allows you to communicate with 4D Systems' screens and controllers.
In stock
+
Add to wish list

US$15.33
This is a basic 16 character by 2 line display. White text on Blue background. Utilizes the extremely common SPLC780D parallel interface chipset.
In stock
+
Add to wish list

US$34.65

This shield allows an Arduino board to visualize informations on an attractive LCD display with white text on blue backlight. 5 push buttons make possible the implementation of projects where menus are visualized on the LCD display and selections are made by the pressure of the buttons, each of them numbered from 1 to 5.

In stock
+
Add to wish list

US$6.29
This is a 24 volt DC red LED.
In stock
+
Add to wish list

US$1.75
CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ.
In stock
+
Add to wish list

US$43.67

Includes: 10cm x 10cm (approx 4"x4") square panel in Aqua, Portable 4xAAA inverter powerful enough to drive a single panel, 4 x AAA alkaline batteries to power the inverter and panel for 10 hours.

In stock
+
Add to wish list

US$34.92

This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in Red, Pocket EL inverter runs on 2 AA Alkaline or rechargeable batteries (not included), 2 inches of heat shink, both 1/8" and 1/4", 2 inches of copper tape, 2 inches of foam tape.

Delivery within 2-3 weeks
+
Add to wish list

US$12.53
The glowing part of the tape is 1 cm wide (the plastic coating is about 1.5cm wide). The other side has an adhesive on it so you can stick the tape onto something.
Delivery within 2-3 weeks
+
Add to wish list