Opto/Illumination

US$18.15
An 1.8 inch TFT LCD that is super useful for small project designs and gives a very sharp/nice picture quality which works amazing well with 3.3v logic level microcontrollers. It is possible to interface with 5v Logic Arduino Microcontrollers by using 1k resistor on the Data Lines or a Level Shifter. Unfortunately this display is not a touchscreen display, however it makes it up with the included SD Card Slot, Not Micro which you finally have a reason to use your SD Card adapters or SD Cards. Soldering not required to get the display to work, but requires some soldering for the SD card functionality (4 soldering holes on the other side).
In stock
+
Add to wish list

US$3.49
This is a case that mounts on top of the 12864 LCD screen. It is made out of ABS plastic and has a matt finish to it.
In stock
+
Add to wish list

US$1.19
Specification: Material: Silicon. Reverse Breakdown Voltage: 15 VDC. Maximum Working Voltage: 10 VDC. Dark Current: 0.3 μA. Light Current: 0.5 – 1 mA.
In stock
+
Add to wish list

US$1.39
This handy 22AWG 4 conductor stranded wire cable is ideal for hooking up multiple connections at a time. Perfect for connecting LED light strips to a controller.  Can be separated into 2 or 3 wire cable easily and used as a universal hook up wire supply. Available in continuous length up to 25 meters long.
In stock
+
Add to wish list

US$3.21
The ILQ2 is a silicon NPN phototransistor. Signal information, including a DC level, can be transmitted by the device while maintaining a high degree of electrical isolation between input and output. The ILQ74 is especially for driving medium-speed logic, where it may be used to eliminate troublesome ground loop and noise problems.
In stock
+
Add to wish list

US$2.70
The ILQ74 is a silicon NPN phototransistor. Signal information, including a DC level, can be transmitted by the device while maintaining a high degree of electrical isolation between input and output. The ILQ74 is especially for driving medium-speed logic, where it may be used to eliminate troublesome ground loop and noise problems.
In stock
+
Add to wish list

US$2.79
This small square shaped LED driver board is based on the WS2812 LEDs that operate at 5VDC and are addressable. Thanks to the small footprint, you can use this board for any applications that has a space constraint. The LEDs are addressable so you can wire a bunch of them provided you are supplying enough current to make a daisy chain. Each board will contain four WS2812 LEDS on board and a small hole in the middle for M3 screw mounting.
In stock
+
Add to wish list

US$7.69
This module is ideally suited to adding a slightly different light display to your project. This module lets you control 8 ultra-bright RGB LEDs to display your information in a bold and bright way, taking your project to new light levels. The LEDs operate at 5v as they are based on the WS2812. Each LED is individually addressable to provide red, blue, green and any combination of them. Unfortunately a printing error in the silkscreen on the module has led to the GND being labelled as VCC.
In stock
+
Add to wish list

US$2.31
An improved package allows superior insulation permitting a 480V working voltage compared to industry standard of 220V.
In stock
+
Add to wish list

US$2.56
An improved package allows superior insulation permitting a 480V working voltage compared to industry standard of 220V.
In stock
+
Add to wish list

US$2.83
This device is a 2 channel optocoupler in a dip-8 package.
In stock
+
Add to wish list

US$2.83
This device is a 1 channel optocoupler in a dip-8 package.
In stock
+
Add to wish list

US$2.79
This is a simple transparent acrylic holder/stand for the 1602 LCDs. This one designed specifically for LCD-MOD-13, however we are certain it will work for any 1602 LCDs. Look at the related product below for compatibility. Unit comes with screws and hex . Please be careful when tighten as acrylic can fracture, you can use super glue to reattached if broken.
In stock
+
Add to wish list

US$0.87
This device is a 940nm radial dark IR photodiode.
In stock
+
Add to wish list

US$10.95
This screen is 25cm wide and 10cm tall offering very small real-estate with a hefty cost, it may seem counter intuitive to buy this display until you realise it is based on OLED. The text are always sharp and clear to read on OLEDs compared to the standard pixel based LCDs. This screen has a higher resolution of pixels 128x32, allowing for more complex designs to be shown. This screen will not require backlight! It runs on four wires and connects via the I2C , so you can start addressing the display or multiple display if want to. All you need to get this display running is some jumper wires and Arduino Microcontroller!
In stock
+
Add to wish list