The WAVE-21225 is an all-in-one kit designed for the Raspberry Pi. It comes with a 5MP, front camera, a 7-inch touch display and a wide array of peripherals for any of your projects.
Specifications
- CM4 SOCKET: suitable for all variants of Compute Module 4
- NETWORKING
- Gigabit Ethernet RJ45
- M.2 M KEY, supports NVME SSD
- Gigabit Ethernet RJ45
- USB: USB 2.0 × 4
- CONNECTOR: isolated RS485, RS232, GPIO, and I2C
- DISPLAY: 7inch, 800 × 480 pixels, 5-points capacitive touch, toughened glass panel
- CAMERA: 5MP, F2.4, 3.89mm fixed focal length, supports video recording
- VIDEO: HDMI, supports 4K 30fps output
- RTC: Real-time clock with a battery socket and ability to wake Compute Module 4
- STORAGE: MicroSD card socket for Compute Module 4 Lite (without eMMC) variants
- FAN: 5V/12V, allows speed adjustment and measurement
- SPEAKER: 8Ω 2W dual-track speakers
- POWER INPUT: 7-36V
- DIMENSIONS: 196.68 × 114.42mm
Interface
What's on Board
| 1 | CM4 socket suitable for all variants of Compute Module 4 |
11 | Isolated I2C for controlling or reading data from devices via I2C |
21 | Speaker header audio output |
| 2 | DC power supply 7 ~ 36V DC input |
12 | Isolated GPIO for controlling or detecting devices via GPIO |
22 | FAN header for connecting cooling fan, allows speed adjustment and measurement |
| 3 | CM4 status indicator PWR: Raspberry Pi power indicator ACT: Raspberry Pi operating status indicator |
13 | Isolated RS485 | 23 | RTC interruption configuration GL-EN: CM4 powerdown on RTC interruption PI-RUN: CM4 will reboot on RTC interruption D16: D16 pin is triggered on RTC interruption (default) |
| 4 | HDMI connector supports 4K 30fps output |
14 | Isolated RS232 | 24 | System function configuration BT_DIS: Bluetooth disabled, for CM4 with antenna variant ONLY WiFi_DIS: WiFi disabled, for CM4 with antenna variant ONLY WP_DIS: boot mode switch, ONLY be used when NOT booted from eMMC or SD card |
| 5 | RJ45 Gigabit Ethernet 10/100/1000M compatible |
15 | DC power supply 7 ~ 36V DC input |
25 | FAN power supply selection select 5V (default) or 12V power to drive the fan |
| 6 | USB 2.0 ports 4x USB 2.0, for connecting sorts of USB devices |
16 | RS485 terminal resistor and GPIO logic level selection RS485: connect/disconnect the 120R resistor GPIO: GPIO logic level selection |
26 | IO-VREF selection set the CM4 IO logic level as 3.3V (default) or 1.8V |
| 7 | Micro SD card slot for connecting a Micro SD card with pre-burnt image (Lite variant ONLY) |
17 | RTC battery holder supports CR1220 button cell |
27 | RS485 switch GPIO13/12: using ttyAMA1 device (default) GPIO15/14: using ttyS0 device |
| 8 | USB SLAVE port USB programming port |
18 | Touch screen header connected to the capacitive touch screen |
28 | RTC/FAN I2C bus selection SDA0/SCL0: I2C-10 is shared with CSI/DSI GPIO3/2: I2C-1 is shared with 40PIN GPIO (default) |
| 9 | BOOT selection ON: CM4 will be booted from USB-C interface OFF: CM4 will be booted from eMMC or Micro SD card |
19 | Display connector connected to the 7inch 800×480 display |
||
| 10 | MIPI CSI connector connected to the 5MP front camera |
20 | M.2 M KEY supports M.2 M KEY NVME SSD, or other communication modules using PCIe channel |
Dimensions
Shipping List
- All-in-one kit x1
- 12V 2A power adapter x1
- Screwdriver x1
