Our Brands

3D /CNC/Mechanical Parts

96 - 110
104 105 106 107 108 109 110 111 112 113 114 115
Newest Items First
15 Per Page
3D-HE-001 Thermistor for 3D printers 100K, 3/pk
US$3.49
This product is a type of resistor where the resistance varies to the temperature. Commonly used as a sensor for sensing temperature for 3D printer extruder and heat beds.
In stock
+ −
Add to wish list
MP-LBB-8 8MM Linear Ball Bearing
US$3.63
These chromium steel ball bearings attach to any smooth linear rods allowing support or movement by attaching using zip ties or specialized clamps.
In stock
+ −
Add to wish list
MP-PG-165 GT2 pulley (16 teeth) for 6mm belts, 5mm Bore Diameter
US$2.79
This pulley connects the motor to the belt and allows for rotational motor movement to translate into linear directional movement. This type of mechanism is most often seen in 3D printers or CNC machines.
In stock
+ −
Add to wish list
BLT-GT2-426 GT2, 2mm pitch, 6mm wide, 426mm long, close-ended Belt
US$6.99
Excellent for linear movement of x and y axis components. The grooves are 2mm and work effectively on 2mm pitch GT2 tooth pulleys. This belt is close-ended, meaning it circular almost like a band belt.
In stock
+ −
Add to wish list
Springs for 3D Printer Heat Bed
US$0.69
Springs are used to support the bed or the extruder to keep the idler pressure constant. The springs create a gap from the heat bed to the base of the printer.
In stock
+ −
Add to wish list
3D-E-004 PCB Heat Bed with Wires for 3D Printer (RED)
US$20.93
The PCB heat bed has two sides, one with the copper traces (bottom side) and one without (top). On older versions of the PCB heat bed, only the side without traces carried a silkscreen.
In stock
+ −
Add to wish list
3D-E-003 Aluminum HeatBed 214x214mm for 3D Printer (BLACK)
US$19.95
This aluminum heat bed is used for 3D printers to help adhere filament onto the bed. Contrary to conventional 3D printer hot beds which have double sided copper traces and silkscreens, this PCB only has copper traces and silkscreen on the top surface.
In stock
+ −
Add to wish list
PS-360-12 Switchable 110/220VAC 12VDC 30A Power Supply
US$35.44
This power supply was designed specifically for 3D printers. The unit is equipped with 3 voltage outputs and common ground terminals. Input: 110/220 VAC ±15%. Output: 30A at 12VDC. Built-in temperature controlled cooling fan. Power cable(s) not included.
In stock
+ −
Add to wish list
3D-H-400 Lead Screw Rod M8x400mm with Collar Nut (Trapezoidal Cut)
US$11.89
This specific thread allows the collar nut to move along the rod and reduces vibration for a better print. Recommended as an improvement for pre-existing RepRap printers that use linear rods.
In stock
+ −
Add to wish list
3D-H-500 Lead Screw Rod M8x500mm with Collar Nut
US$12.60
This specific thread allows the collar nut to move along the rod and reduces vibration for a better print. Recommended as an improvement for pre-existing RepRap printers that use linear rods.
In stock
+ −
Add to wish list
3D-E-002 Mechanical Limit Switch Breakout Board
US$2.09
This device employs a standard miniature limit switch on a breakout board with a detachable JST connection cable included. Once the 3D printer/CNC frame axis reaches the end of the shaft as the motor slides down, the limit switch pushes up against the casing barrier and stops its motion.
In stock
+ −
Add to wish list
CAB-3P-FF-70CM 3 Pin Female/Female Jumper Wire - 70cm (27.5’’)
US$2.09
These wires are extremely handy for extending or bridging 3 pin devices. Common uses include sensors and servo motors. They attach easily onto headers and boards. Each wire is gauge 26 AWG and can withstand up to 300V.
In stock
+ −
Add to wish list
CAB-4P-FF-70CM 4 Pin Female/Female Jumper Wire - 70cm (27.5’’)
US$2.09
These wires are extremely handy for extending or bridging 4 pin devices. They attach and detach easily to and from headers and boards. Each wire is gauge 26 AWG and can withstand up to 300V.
In stock
+ −
Add to wish list
CAB-2P-FF-70CM 2 Pin Female/Female Jumper Wires 70cm (27.5’’)
US$2.09
These jumper cables are extremely practical for extending or bridging connections. This 2 pin female to female are commonly used for extending battery/power lines or running wires to and from motors and LEDs.
In stock
+ −
Add to wish list
FAN-3D Fan Brushless 12VDC for 3D Printer (40mm x 40mm x 10mm)
US$3.49
This brushless fan is primarily used for installation in a 3D printer. The fan serves to cool down the motors and filament during lengthy prints. The fan is easily connected via a 2 pin JST connector.
In stock
+ −
Add to wish list
96 - 110
104 105 106 107 108 109 110 111 112 113 114 115