3D /CNC/Mechanical Parts

US$2.65
The following is a drive gear for your extruders stepper motor. Place this part on the shaft of your stepper motor and you can then use it as a pulley to feed the hot end with your filament.
In stock
+
Add to wish list

US$2.72
This is a connector/adaptor typically found on the extruder section for 3D printers or pneumatic. This product simplifies the task of supplying your nozzle 1.75mm filament.
In stock
+
Add to wish list

US$72.75
This special product is a kit that comes with the following items prepackaged; 1x 200mm M8 Lead Screw Rod, 2x 200mm M8 Linear Shaft Rods, 4x 8mm Diameter Linear Motion Ball-Bearing Slide Pillow Blocks, 2x 8mm Diameter Pillow Block, 4x 8mm Linear Rod Clamp, 2x 5mm to 8x34.5mm Flexible couplers, 1x M8 Lead Screw Nut.
In stock
+
Add to wish list

US$1.99
The following is a stainless steel throat with Teflon PTFE tubing for additional protection. The Teflon helps against gradual wear of the tube against abrasive filaments (such as wood) .
In stock
+
Add to wish list

US$2.37
The following is an aluminum heat block, an essential part for any DIY 3D printer projects. Use the M6 hole in the center to place your nozzle and extruder throat.
In stock
+
Add to wish list

US$1.81
A thermistor is a resistor whose value varies with temperature. This type of device is rated at 100K ohm. This particular product is used as replacement 3D printers extruder and heat bed to serve as temperature sensors.
In stock
+
Add to wish list

US$2.79
If you require additional cooling for your steppers motors, this product will do just that. It has a profile of 40x40x11 mm and is made out of zinc metal material. Excellent for CNC and 3D related projects that require passive cooling.
In stock
+
Add to wish list

US$1.25
This is a heavy duty aluminum radiator 15D3DD model heat sink for the TO-3 power transistor package.
In stock
+
Add to wish list

US$1.99

This very handy fabric (often referred to as “loom”) is used for wrapping and protecting wires. Every serious project should consider wire management as a finishing touch.

In stock
+
Add to wish list

US$18.13
This PCB heat bed has two sides, one with the copper traces (bottom side) and one without (top). On older versions of the PCB heat bed, only the side without traces carried a silkscreen.
In stock
+
Add to wish list

US$8.99
This is a simple extrusion mechanism that is attached to your stepper motor, filament and Bowden coupler. Used to control the feed rate of the filament sent to the nozzle. You will need to purchase the motor, filament and coupler separately.
In stock
+
Add to wish list

US$2.37
This product is a sleeve bearing or also known as a bushing for M8 Linear rods or shafts. They can be found or applied for axis movement applications as a replacement for ball bearings.
In stock
+
Add to wish list

US$2.37
This product is a sleeve bearing or also known as a bushing for M8 Linear rods or shafts. They can be found or applied for axis movement applications as a replacement for ball bearings.
In stock
+
Add to wish list

US$2.51
This product is a sleeve bearing or also known as a bushing for M8 Linear rods or shafts. They can be found or applied for axis movement applications as a replacement for ball bearings.
In stock
+
Add to wish list

US$15.33
This unit is a E3D-V6 Direct Hot End, designed to be attached to the x-axis of your 3D printer. This unit comes with a Bowden coupler for 3mm filament specifically and one heatsink chamber with a 3mm filament throat with PTFE that will feed your filament to the heating block.
In stock
+
Add to wish list