This is a DC 12V 24V 36V 48V Power Converter Module: Input voltage DC10V~60V; Output voltage DC 12~60V; adjustable default 19V); Output current 10A MAX.
Application: DIY Power adapter/Charger, industrial equipment, electronic equipment, communications equipment, power tools LCD TV, Advertising screens, LED lights, Fan, intercom and monitoring systems, etc.
Parameters:- Input voltage: DC10V~60V
- Input current: 10A MAX
- Quiescent current: 10mA (12V to 20V, the higher the output voltage, the quiescent current will increase.
- Output voltage: DC 12~60V adjustable（default 19V)
- Output current: 10A MAX (Please strengthen the cooling of more than 6A)
- Constant current range: 0.2~10A
- Output power= Input voltage *10A，e.g. 12V*10A=120W; 24V*10A=240W
- Working temperature: -40~+85 degree (Please strengthen the heat dissipation when the ambient temperature is too high.)
- Working frequency: 150KHz
- Transfer efficiency: 92%-96%
- Installation: 4*3mm screw hole
- 1.VIN+:input power positive, VIN-: input power negative
- 2.OUT+: output power positive, OUT-: output power negative.
- 3.Adjustable constant voltage rang: DC12~60V（clockwise to increase，counterclockwise to decrease）
- 4.Adjustable constant current rang：0.2~10A（clockwise to increase，counterclockwise to decrease）
- 5.Please strengthen the cooling when the input current is over 6A（The aluminum substrate is attached to the flat metal parts）
- 6.The input voltage cannot be lower 10V or higher 60V.
- 7. The input current cannot exceed 10A and the power cannot be exceed 600W.
- 8. It must be ensure that the input voltage lower 2V above than the output voltage.
- 9. Before connecting to the load, please adjust the required voltage and current when no-load (the no-load voltage should be adjusted high 3-5v in the constant current)
- 10. When using switching power supply or other secondary power supply, please ensure that the power of power supply should be greater than more than module power more than doubled.
- 1.Adjust the output voltage:
- Adjust CV-ADJ potentiometer, clockwise to increase, counterclockwise to reduce. According to the battery /LED, set the output voltage you desired.
- 2. Adjust the output current:
- Clockwise CC-ADJ potentiometer about 20 laps, the output current set to the minimum value, connect the LED, adjust the CC-ADJ potentiometer to the current you need. For battery charging, after the battery has been discharged, and then connect to the output, adjust CC-ADJ to your required current. (When using for charging, it must be adjusted with the discharge battery, because the battery remains in the more power, the smaller the charging current. ）
- NOTE: Please do not use the short-circuit method to adjust the current, because the circuit structure of the booster module cannot be adjusted in the short-circuit way.
- 1. The input and output wires cannot be connected reversed.
- 2. The input voltage is not less than 10V, too low input voltage will damage the power supply. (When using the battery should pay attention to the battery over-discharge). When it is working, the input/output voltage and the input/output current cannot exceed the maximum values, so as not to damage the battery.
- 4. In the long-term full load working, it should be taken note of ventilation and cooling, to extend the life of the power supply.
- 5. Also pay attention to dust and moisture.
- 1. DIY a stabilized voltage supply, the input can be 12V, the output can be 12-50V adjustable.
- 2. It can supply power for your electronic equipments; you can set the output value according to your system voltage.
- 3. As a car power supply, supply for your laptop, PDA or a variety of digital products.
- 4. DIY a high-power notebook power bank: coupled with a large capacity of 12V lithium battery pack, so that your books can light up wherever.
- 5. Solar battery panels regulate voltage.
- 6. Charge for the battery, lithium battery, etc.
- 7. Drive high power LED lights.
WARNING
