Our Brands

Thermal Management

1 2 3 4 5 6 7 8 9 10 11 12
Newest Items First
15 Per Page
PI-SMARTFAN Smart Temperature Control Fan and Power Expansion Board for Raspberry Pi
US$27.93
This smart fan and power expansion board are designed for DIY makers, especially for Raspberry Pi lover, it is compatible with Raspberry Pi 3/ 2B/ B+. Built-in temperature sensor, with active cooling fan, you can control flexibly the ON/OFF of mini fan via I2C command and GPIO programming.
In stock
+ −
Add to wish list
HS-280 General Purpose Aluminum Heat Sink - 100x41x8mm
US$7.23
This heatsink is thin, long and wide which makes it suitable for applications where multiple heat sources can share the same heatsink such as: high wattage LEDs, transformers, peltiers etc..
In stock
+ −
Add to wish list
574502B00000G Heat Sink T0-220 Vertical Slide-on
US$0.83
This device is an aluminum vertical slide-on TO-220 package heat sink without tabs. Features...
In stock
+ −
Add to wish list
TEC1-12704 12VDC 2.5A 30 Watt Thermoelectric Peltier Cooler Plate
US$10.77

Also known as the Magic Plate, this cooler uses Peltier effect that can generate electricity! Essentially when you apply power to one side, it will heat up and the other side will cool down. If you create a differential system you could essentially generate electricity but not enough to charge your phone…

In stock
+ −
Add to wish list
TEC1-12705 12VDC 5A 60 Watt Thermoelectric Peltier Cooler Plate
US$10.00
Also known as the Magic Plate, this cooler uses peltier effect that can generate electricity! Essentially when you apply power one side will heat up and the other side will cool down. If you create a differential system you could essentially generate electricity but not enough to power you phone. Typically the side with Product number is the cooled side and the back side is the warm side. You can test this by applying 1.5v from a AA battery on the leads for 5-10 seconds and feeling the plate. We recommend placing a heatsink on the hot side to optimal performance. This module is a 12V module, and is rated for ~60W (70W max) so we suggest a 12V/5A or higher amperage adapter for use.
In stock
+ −
Add to wish list
FAN-3D-004 12VDC 1A 40x40x28mm 43CFM 4-Pin Delta Fan
US$19.95
This is a small yet powerful fan that is capable of pushing about 43 CFM. It has dual ball bearings on the output shaft making it relatively quiet for the amount of thrust it can provide.
Delivery within 2-3 weeks
+ −
Add to wish list
HS-250 35mm Diameter 540/550/560 Motor Heatsink
US$4.94
This is a heatsink that mounts onto your 35mm diameter motor. It keeps your motor cool and increases its life longevity. It is great for motors that are constantly used for long periods of time such as in CNC machines.
In stock
+ −
Add to wish list
HS-260 Darlington Transistor Heatsink (pack of one)
US$0.69
This is a heatsink that mounts onto your Darlington Transistor. It keeps the temperature of your transistor cool and increases its life longevity.
In stock
+ −
Add to wish list
TEC1-04904 Thermoelectric Peltier Cooler 13.5 Watt
US$15.32
TEC's can be used for heating or cooling depending on which way the current flows by simply reversing the connections. Heating or cooling speed can be changed by increasing or decreasing the voltage applied. TEC’s are solid state, reliable, noise free and vibration free, suitable for applications that have limits on space, noise and vibration. TEC’s are widely used in industrial instrument heating and cooling, commercial wine coolers and portable picnic coolers.
In stock
+ −
Add to wish list
TEC1-04905 5VDC 5Amp 25 Watt Thermoelectric Peltier Cooler Plate
US$13.01
Also known as the Magic Plate, this cooler uses Peltier effect that can generate electricity! Essentially when you apply power one side will heat up and the other side will cool down. If you create a differential system you could essentially generate electricity but not enough to power you phone… Typically the side with Product number is the cooled side and the back side is the warm side. You can test this by applying 1.5v from a AA battery on the leads for 5-10 seconds and feeling the plate. We recommend placing a heatsink on the hot side to optimal performance. This module is a 5V module, and is rated for ~29W max (up to 5V/5.8A) but when used with a regulated 5V output they don't draw more than 5A so we suggest a 5V/5A power adapter for use.
In stock
+ −
Add to wish list
TEC1-03104 Thermoelectric Peltier Cooler 12 Watt
US$12.31
These thermoelectric coolers (TEC) operate according to the Peltier effect. TEC's can be used for heating or cooling depending on which way the current flows by simply reversing the connections. Heating or cooling speed can be changed by increasing or decreasing the voltage applied. TEC’s are solid state, reliable, noise free and vibration free, suitable for applications that have limits on space, noise and vibration. TEC’s are widely used in industrial instrument heating and cooling, commercial wine coolers and portable picnic coolers.
In stock
+ −
Add to wish list
FAN-3D-002 12VDC 0.15A Blower Fan (Part Cooling Fan for 3D printers)
US$5.59
This is a special type of fan that can be found in 3D printers. Commonly referred as the vortex fan, this fan is excellent for cooling your parts as the nozzle of your printer lays the molten plastic (especially when using PLA material).
In stock
+ −
Add to wish list
SP1848-27145 Thermoelectric Peltier Cooler Plate – 4.8VDC 670mA 3.2W
US$9.23
Thermoelectric coolers (TEC) operate according to the Peltier effect. The effect creates a temperature difference by transferring heat between two electrical junctions. When the current flows through the junctions of the two conductors, heat is removed at one junction and cooling occurs at the other. Therefore, TEC’s can be used for heating and cooling, depending on which side you use. Either side will heat up or cool down very quickly until it reaches equilibrium, so the heat needs to be managed with a fan or heatsink to keep the process going.
In stock
+ −
Add to wish list
FAN-9025 12 VDC Cooling Fan – 9.2 x 9.2 x 2.4cm
US$4.19
This is a 12VDC rated computer cooling fan with 2-pin JST connector. The fan has a black case with holes for screw mounting that are 8.3 x 8.3 apart and can fit M5 screws or smaller. NOTE: This is a 2-wire fan and therefore does not have the ability to measure speed.
In stock
+ −
Add to wish list
FAN-6015 12VDC 200mA Generic Fan with 2 Pin JST connector – 6x6x1.5cm
US$4.19
This product is a generic DC fan that operates at 12VDC, it will consume 200mA to run at nominal speeds. This fan is recommend for a any component that requires ventilation and will mount on any mounting hole that is 5x5cm apart. You can mount this product using a generic M3 or M4 screw. This fan has a JST pin for power and measures 6x6x1.5cm.
In stock
+ −
Add to wish list
1 2 3 4 5 6 7 8 9 10 11 12