Our Brands

Thermal Management

1 2 3 4 5 6 7 8 9 10 11 12 13
Newest Items First
15 Per Page
14mmx14mmx6mm Aluminum Adhesive Heatsink
US$0.69
This heatsink is designed specifically for any TO package based IC. It can also be used for any chip that requires heat to be dissipated. This heatsink is composed of high-grade aluminum and offers some decent thermal performance. Recommend to be used on, VGA, CPU, GPU, RAM, LM, TIP, IRF and any other TO based Package IC. Has heat conductive tape on the base to simplify attachment.
In stock
+ −
Add to wish list
3pcs Heatsink for Raspberry Pi 4 Model B
US$2.99

This Heat Sink Cooler Kit For Cooling your Raspberry Pi includes 3 aluminum heat sinks with adhesive backing.

In stock
+ −
Add to wish list
Dedicated Cooling Fan for Jetson Nano, 5V, 3PIN Reverse-proof
US$2.79
Category: Jetson Nano cooling fan. Connector: 3PIN reverse-proof connector. Spec: 5V. Dimensions: 40mm×40mm×10mm.
In stock
+ −
Add to wish list
Dedicated Cooling Fan for Jetson Nano, PWM Adjustment
US$4.19
Category: Jetson Nano cooling fan. Connector: 4PIN reverse-proof connector. Spec: 5V, PWM adjustment. Dimensions: 40mm×40mm×20mm.
In stock
+ −
Add to wish list
TO-220 Aluminum Heat Sink
US$2.98
Specification: Material: 6063 Black anodized aluminum. Dimensions: 30 x 35 x 20mm. Mounting Pins: 2mm Diameter. Pin spacing: 19mm.
In stock
+ −
Add to wish list
Insulation Cotton Washer for TEC1-12706 Cooler
US$0.54
This is an Insulation Cotton washer suitable for TEC1-12706 Thermoelectric cooler, which is widely used for refrigeration.
In stock
+ −
Add to wish list
FAN-330, 24 VDC 120x120x38mm Brushless Tubeaxial Fan 107 CFM, 12 Inch Wires
US$22.70
This is a 24 Volt DC 120x120x38mm Brushless Tubeaxial Fan 107 CFM, 2800 rpm Specifications Model: GD241238MB Voltage: 24 volts DC Size (W x...
In stock
+ −
Add to wish list
24V 4cm Cooling Fan
US$5.59
It is a 24V DC operating Colling fan suitable for graphics cards , 3d printers and laptops. This is small in size and can fit in any small compartment or case. Comes with 2 pin JST connector.
In stock
+ −
Add to wish list
Fan 4020 DC 12V
US$4.89
This is a 12 VDC fan with JST-XH power connector.
In stock
+ −
Add to wish list
Aluminum Adhesive Heatsink 14mmx14mmx4mm
US$0.59
This heatsink is designed specifically for any TO package based IC. It can also be used for any chip that requires heat to be dissipated. This heatsink is composed of high-grade aluminum and offers some decent thermal performance. Recommend to be used on, VGA, CPU, GPU, RAM, LM, TIP, IRF and any other TO based Package IC.
In stock
+ −
Add to wish list
PI-SMARTFAN Smart Temperature Control Fan and Power Expansion Board for Raspberry Pi
US$27.93
This smart fan and power expansion board are designed for DIY makers, especially for Raspberry Pi lover, it is compatible with Raspberry Pi 3/ 2B/ B+. Built-in temperature sensor, with active cooling fan, you can control flexibly the ON/OFF of mini fan via I2C command and GPIO programming.
In stock
+ −
Add to wish list
HS-280 General Purpose Aluminum Heat Sink - 100x41x8mm
US$7.23
This heatsink is thin, long and wide which makes it suitable for applications where multiple heat sources can share the same heatsink such as: high wattage LEDs, transformers, peltiers etc..
In stock
+ −
Add to wish list
574502B00000G Heat Sink T0-220 Vertical Slide-on
US$0.83
This device is an aluminum vertical slide-on TO-220 package heat sink without tabs. Features...
In stock
+ −
Add to wish list
TEC1-12704 12VDC 2.5A 30 Watt Thermoelectric Peltier Cooler Plate
US$10.77

Also known as the Magic Plate, this cooler uses Peltier effect that can generate electricity! Essentially when you apply power to one side, it will heat up and the other side will cool down. If you create a differential system you could essentially generate electricity but not enough to charge your phone…

In stock
+ −
Add to wish list
TEC1-12705 12VDC 5A 60 Watt Thermoelectric Peltier Cooler Plate
US$10.00
Also known as the Magic Plate, this cooler uses peltier effect that can generate electricity! Essentially when you apply power one side will heat up and the other side will cool down. If you create a differential system you could essentially generate electricity but not enough to power you phone. Typically the side with Product number is the cooled side and the back side is the warm side. You can test this by applying 1.5v from a AA battery on the leads for 5-10 seconds and feeling the plate. We recommend placing a heatsink on the hot side to optimal performance. This module is a 12V module, and is rated for ~60W (70W max) so we suggest a 12V/5A or higher amperage adapter for use.
In stock
+ −
Add to wish list
1 2 3 4 5 6 7 8 9 10 11 12 13