This Digital Inspection Endoscope is a utility class equipment with the function of real-time video viewing, video recording and picture capturing, etc... which is suitable for usage in narrow area and the area which cannot be observed by sight , such as: vehicle repair, sewer inspection/maintenance, etc.
Safety Warning:
- WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.
Product features:
- 2.4-inch ips HD display for real-time viewing of test videos
- Support for taking photos and videos
- 180 degrees image mirroring
- TF card can be installed to achieve file storage function
- High sensitivity waterproof lens with clear image quality for different working environments
- Special technology with a focal length of 4cm-8cm
- Auxiliary light source, 6 adjustable LED lights and a flashlight for easy use in dark environments
- IP67 waterproof
Technical parameters:
- Model: INskam128
- Monitor: 2.4 inch ips HD screen
- Horizontal viewing angle: 70 degrees
- Language: English, German, Simplified Chinese, Spanish, French, Russian, Japanese
- Line length: 5m
- Focal length: 4cm-8cm
- Waterproof level: IP67 (only for lens/lamp)
- Battery capacity: 2600mAh
- Battery endurance: About 2 hours
Application:
- Tubular/Water Pipe Cleaning: It helps to clean rust, corrosion, dust and crack after the pipe is inspected
- Shipbuilding industry: used to inspect boilers, steam turbines, diesel engines, pipelines
- Industrial machinery: used to check for engine scars or wear, gearboxes, hydraulic systems, greatly reducing downtime
- Electronics, electronics industry: used to confirm the wiring status of the product, check the working condition of the machine, etc.
Accessories list:
- Digital Inspection Endoscope
- User manual
- USB data cable
- Accessories - hook, magnets, side mirrors, protective cap
- DC-5100-USB - Switching Power Supply 5VDC 1A with USB Connection (NOT INCLUDED)
Digital Inspection Endoscope features:
- Part name and function:
- Micro TF card slot
- DC 5V input
- Charging Indicator
- Photo/Video/OK button
- Light adjustment/down button
- Back/File view button
- Settings/Power button
- Hard tube
- Function introduction
- Micro TF card slot: Supports up to 64GB microTF card, only supports TF cards with class 10 or highter FAT32 format(not equipped with this unit)
- Micro seat: DC 5V power supply
- Rotate/Up button: Photo mode, up and down. Other modes, move up or left
- Recording/OK button: Photo mode, short press to take a photo, long press to take a video, then press to stop. Other modes, short press to confirm
- Light adjustment/Down button: Photo mode, short press light adjustment, including four brightness cycles. Other modes, moving down or to the right
- Return/File view button: Photo mode, short press file view. Other modes, short press to return to the previous menu modes, move up or left
- Setup/Power button: Short press to enter the setting page, press and hold for 3 seconds to power on and off
- Charging Indicator: The charging indicator on the left side is always red when charging,and automatically turns off when fully charged
Installation Notes:
- Installation accessories: 4 accessories - hooks, magnets, fixing device, Side mirror installation
Steps for usage:
- Basic operation
- Insert the MicroTF card(not equipped with unit) into the MicroTF card slot; press gently until the card is locked
- Press and hold the Settings/Power button to turn on the device, then adjust the brightness of the camera with the light adjustment buttons
- Press and record button to take a photo, long press the recorded video, press again to stop recording
- Charging
- Please use the 5V 1A adapter (ABRA#: DC-5100-USB) or connect it to the computer to charge the device. When the battery is charging, the charging indicator on the left side of the display will be red
- After the battery is fully charged, the charging indicator will go out and the power plug will be unplugged. The entire charging process takes about 2 hours
- After fully charging, you can continue to use the device for about 2 hours. When the battery is low, the display will show a low battery. Then you must connect the power adapter and plug it into the battery. (Note: The device is completely dead. Under, the charging time must be at least 1 hour to be used normally)
- Troubleshooting
- Problem: Device cannot be turned on
- Solution: Does the battery have electricity?
- Solution: Has the power been successfully connected?
- Problem: TF card reading is unsuccessful
- Solution: Is the memory card format correct? (This device only supports FAT32 file format)
- Solution: Re-insert the TF card after removing it
- Problem: After the device is connected to the PC, the TF card cannot be read
- Solution: Reconnect the device and PC
- Solution: Confirm whether to enter the mass storage mode
- Problem: Device crash
- Solution: Plug in the USB data cable to charge, automatically shut down, then press the power button to reset
- Problem: Smudged or smeared on the screen
- Solution: Carefully clean the screen with a soft cloth
- Problem: Device cannot be turned on
FCC Information:
- This device complies with PART 15 of the FCC Rules.
- Subject to the following two conditions:
- (1) This device does not cause harmful interference
- (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment
EU Environmental Protection:
- Waste electrical products should not be disposed of with household waste
- Please consult your local government or retailer for recycling advice
- If the number contained in the user manual has minor changes without prior notice
WARNING
