WAVE-29687, Raspberry Pi Compute Module 5 IO Board, PoE Mini - Computer Kit
Compute Module 5 PoE Base Board
Suitable for evaluating the Raspberry Pi CM5 or being integrated into end products
PoE Base Board for all Compute Module 5 Variants
Specifications:
CM5 SOCKET: suitable for all variants of Compute Module 5
NETWORKING: Gigabit Ethernet RJ45 connector, integrates 802.3af/at-compliant PoE circuit (5V/5A)
CONNECTOR: Raspberry Pi 40PIN GPIO header
USB: USB 3.2 Gen1 × 2, USB 2.0 × 2
MIPI: 4-lane MIPI interface × 2 (22pin 0.5mm FPC connector)
VIDEO: HDMI port × 2, supports 4K output
RTC: CR / ML2032 battery holder
STORAGE: TF card slot for Compute Module 5 Lite (without eMMC) variants
FAN CONNECTOR: 5V, JST-SH PWM 4PIN connector
NVME: PCIe Gen2/3 × 1
POWER INPUT: 5V 5A
DIMENSIONS: the base board: 160 × 90 (mm), with metal case: 200.5 × 97.5 × 31.0 (mm)
Connecting With Compute Module 5
Standard CM5 Socket and Raspberry Pi 40Pin GPIO Header
Suitable for All Variants of Compute Module 5
Power Over Ethernet
Providing Both Network Connection and Power Supply For Your Raspberry Pi in One Cable
Support M.2 NVMe Solid State Drive
Faster reading/writing speed compared to the TF card slot of Raspberry Pi, greatly improving reading/writing efficiency of the system or files, support booting Raspberry Pi from NVMe Solid State Drive
For reference only: SSD not included.
Compatible with Multiple Sizes
NVMe Drive Slot Support
Note: Only supports NVMe Protocol Solid State Drives.
Rich Peripheral Connectors
Onboard connectors including MIPI / M.2 / HDMI / USB / ETH / TF Card Slot
Precise Cut-Out With Clear Label
Each Cut-Out Is Completely Aligned With the Connector
Cooling Fan Included
Comes with Cooling Fan, Combined with the Airflow Vent, Better Head Dissipation
Wall Mount Support
Wall Mount Holes On Two Sides, Handy for Mounting
What's On Board
- CM5 socket
Suitable for all variants of Compute Module 5 - USB Type-C power supply / programming
5V/5A power supply, also allows burning system image into Compute Module 5 variants - M.2 Solid State Drive indicator
Keeps blinking while reading/writing - M.2 M key
Compatible with 2280/2260/2242/2230 NVMe drives or AI accelerator module - Dual MIPI interfaces
for connecting DSI LCDs or CSI cameras - PSW button
power button - 40PIN GPIO header
for connecting various HATs - RTC battery holder
Supports CR/ML2032 button cell - HDMI ports
2x HDMI ports, supports dual 4K output - Status indicators
ACT: Raspberry Pi operating status indicator
PWR: Raspberry Pi power indicator
- USB2.0 ports
2x USB2.0 ports, for connecting sorts of USB devices - USB 3.2 Gen1 ports
2x USB 3.2 Gen1 high-speed ports, supports 5Gbps synchronous operation - Gigabit Ethernet connector
Gigabit Ethernet RJ45 with PoE support - FAN connector
for connecting cooling fan - Misc configurations
for extending other functions - IO-VREF/PoE selection
CM5 IO logic level: 3.3V or 1.8V
PoE: enable (EN) or disable (DIS) - CAM1 and DISP1 I2C bus
fit the jumpers when using CAM1 or DISP1 - TF card slot (bottom side)
insert a TF card with pre-burnt system, to start up Compute Module 5 Lite
Dimensions:
PoE Base Board
PoE Mini-Computer Kit
WARNING
