Our Brands

Robotics - Actobotics/ Servocity/goBILDA

Welcome to ServoCity where you can get the parts you need to bring your ideas to life! From servos to switches, from actuators to Actobotics to goBILDA, we work hard to bring you the best components backed by unparalleled technical support.

55 - 69
63 64 65 66 67 68 69 70 71 72 73 74 75 76 77
71 - 85
Newest Items First
15 Per Page
4100-0608-0100 (6mm ID x 8mm OD, 100mm Length) 4100 Series Aluminum Tube
US$4.50
6mm ID x 8mm OD Aluminum Tubing can be used to add structural support to a lightweight chassis, as an axle in a rotating assembly or as a sleeve over a 6mm shaft, spacer or standoff.
In stock
+ −
Add to wish list
4100-0608-0050 (6mm ID x 8mm OD, 50mm Length) 4100 Series Aluminum Tube
US$3.87
6mm ID x 8mm OD Aluminum Tubing can be used to add structural support to a lightweight chassis, as an axle in a rotating assembly or as a sleeve over a 6mm shaft, spacer or standoff.
In stock
+ −
Add to wish list
585716, 25mm Bore Bottom Tapped Clamping Mount (Actobotics)
US$8.87
This 25mm bore clamping mount holds a 25mm motor off of the surface the mount is fastened to. The 6-32 threaded holes match up with the side of the 1.5” pattern (measuring 1.061” apart).
In stock
+ −
Add to wish list
545680 25mm Bore Side Tapped Clamping Mount (Actobotics)
US$9.96
This clamping mount is designed for use with our Economy Spur Gear Motors but can also be used on 25mm OD shafting and tubing. It has (4) 6-32 tapped side mounting holes that provide a perfect fit inside Actobotics Channel.
In stock
+ −
Add to wish list
1704-0016-0001 Acetal Plastic Mount for Econ/Mini Econ Gear Motor (16-1) (goBILDA)
US$3.14
Weight: 3.4g with M2.5 Screws for Mini Econ Gear Motor, 3.8g with M3 Screws for Econ Gear Motor. Material: Acetal Plastic. Included Hardware for Mini Econ Gear Motor: Two 6mm Length M2.5 #1 Philips Drive Flat Head Screws. Included Hardware for Econ Gear Motor: Two 8mm Length M3 #1 Philips Drive Flat Head Screws.
In stock
+ −
Add to wish list
1302-0032-0025 1302 Series Clamping Hub (25mm Bore) (goBILDA)
US$9.96
Weight: 18g. Material: Aluminum. Finish: Clear Anodized.
In stock
+ −
Add to wish list
1206-0016-0004 1206 Series Pattern Adaptor (16-4) (goBILDA)
US$8.87
This pattern adaptor contains thru-holes for M4 screws on the goBILDA 16mm pattern, 6-32 UNC threaded holes on the Actobotics 0.77" hub pattern and thru-holes for 6-32 screws on the Actobotics 1.5” hub pattern. Use it to adapt a 5202 Series Yellow Jacket Gear Motor to your Actobotics assembly or fasten structural components together with ease when mixing the two systems.
In stock
+ −
Add to wish list
1206-0016-0007 Threaded Actobotics to Thru-Hole goBILDA Pattern Adaptor (16-7) (goBILDA)
US$8.87
The thru-holes on this adaptor align with the 16mm pattern found on almost every goBILDA part but are slotted outward for edge-case situations where you need to align with holes spaced 24mm across the center. The counterbores allow heads of M4 socket head screws to rest below the top surface so you have a clean slate to fasten a part to. The counterbores are machined as a hex-profile in order to accept and capture an M4 locknut if you prefer to have screws come up through the bottom.
In stock
+ −
Add to wish list
555172 Planetary Gear Motor Mount A (Actobotics)
US$7.95
This mount is perfect for mounting a Premium Planetary Gear Motor on the Actobotics 0.77" pattern. The counterbored holes accept the included 2mm pan head screws to fasten the motor to the mount, leaving the face flush for ease of mounting to channel or other components.
In stock
+ −
Add to wish list
545666 22mm Bore, Face Tapped Clamping Hub, 1.50" Pattern (Actobotics)
US$9.96
This 22mm clamping hub matches the OD of our Premium Planetary Gear Motors. You can fasten the hub to an Actobotics component, using the threaded holes on the 1.5" pattern and then slide your motor in the hub and clamp it down. Using a clamping hub for a motor mount makes disassembly for service or reconfiguring very easy.
In stock
+ −
Add to wish list
1305-0032-0022 1305 Series Thru-Hole Clamping Hub (22mm Bore) (goBILDA)
US$9.96
Weight: 19g. Material: Aluminum. Finish: Clear Anodized.
In stock
+ −
Add to wish list
1302-0032-0022 1302 Series Clamping Hub (22mm Bore) (goBILDA)
US$9.96
Weight: 19g. Material: Aluminum. Finish: Clear Anodized.
In stock
+ −
Add to wish list
555198 REV Core Hex Motor Mount (Actobotics)
US$8.87
The REV Core Hex Motor Mount allows you to fasten the REV Core Hex motor to any Actobotics component that contains thru holes on the 1.5" pattern. This mount comes with (8) M3 x 8mm length screws to pass through the motor mount and into the threaded holes of the REV motor.
In stock
+ −
Add to wish list
1701-0032-0001 1701 Series Face Tapped Motor Mount (32-1) (goBILDA)
US$9.96
This motor mount is designed to be used with the REV Robotics Core Hex Motor. Given this motor is used in FIRST Tech Challenge, we want to provide teams the opportunity to easily integrate the motor into their goBILDA framework. When you use two mounts (one on each side), the side-to-side measurement will be exactly 43mm so the assembly will slide down inside 1120 Series U-Channel perfectly and fasten using M4 x 6mm length screws.
In stock
+ −
Add to wish list
1702-0043-0003 1702 Series Quad Block Motor Mount (43-3) (goBILDA)
US$13.42
This motor mount aligns with the REV UltraPlanetary Gearbox and provides a plethora of mounting options with your goBILDA chassis. The C-shaped design provides a thru-way to access the set-screw on the UltraPlanetary’s output hub. If 5mm hex isn’t your thing, beef up the output with our 8mm REX shaft which is able to bolt directly onto the UltraPlanetary using the REV orbital pattern found on the face of their output hub.
In stock
+ −
Add to wish list
55 - 69
63 64 65 66 67 68 69 70 71 72 73 74 75 76 77
71 - 85