Our Brands

WAVE-10207 4inch RPi LCD (A), 320×480, IPS

Manufacturer: Waveshare
Price:
US$44.79
WAVE-10207
In stock
+ −
Add to wish list

WAVESHARE 10207 4inch RPi LCD (A), 320×480, IPS

Features

  • Designed for Raspberry Pi
  • Supports any revision of Raspberry Pi (directly-pluggable)
  • Drivers provided (works with your own Raspbian/Ubuntu directly)
  • IPS technology, high quality and perfect displaying from very wide viewing angle
  • 320×480 resolution
  • Convenient Men-Machine interface for Raspberry Pi, combined with the portable power, DIY anywhere anytime
  • Supports Raspbian system, enables your system to:
    • Take photos by touching (up to 17 camera modes)
    • Support software keyboard (system interaction without keyboard/mouse)

Key Parameters

LCD Type TFT
LCD Interface SPI
Touch Screen Type Resistive
Touch Screen Controller XPT2046
Colors 65536
Backlight LED
Resolution 320*480 (Pixel)
Aspect Ratio 8:5
Power Consumption TBD
Backlight Current TBD
Operating Temp. (℃) TBD

Interface

PIN NO. SYMBOL DESCRIPTION
1, 17 3.3V Power positive (3.3V power input)
2, 4 5V Power positive (5V power input)
3, 5, 7, 8, 10, 12, 13, 15, 16 NC NC
6, 9, 14, 20, 25 GND Ground
11 TP_IRQ Touch Panel interrupt, low level while the Touch Panel detects touching
18 LCD_RS Instruction/Data Register selection
19 LCD_SI / TP_SI SPI data input of LCD/Touch Panel
21 TP_SO SPI data output of Touch Panel
22 RST Reset
23 LCD_SCK / TP_SCK SPI clock of LCD/Touch Panel
24 LCD_CS LCD chip selection, low active
26 TP_CS Touch Panel chip selection, low active

External Dimension

Downloads

Development resources:Image, schematic, dimension, software, etc.
Download: www.waveshare.com/wiki/4inch_RPi_LCD_(A)

FAQ

Why the LCD doesn't work with my Raspbian?
To use the LCD with the Raspberry Pi official image, driver should be installed first. Please refer to the user manual.
However, for the first testing, you may want to use our provided image directly.
Why the LCD still doesn't work with the Waveshare provided image?
Make sure the hardware connection is correct and connects fine.
Make sure the image in TF card is burnt correctly.
The PWR will keep on and the ACT will keep blinking when the Raspberry Pi starts up successfully, in case both of the two LEDs keep on, it is possible that the image was burnt incorrectly OR the TF card was in bad contact.
Which power supply should I use?
It is strongly recommended to use a stand-alone 5V/2A power adapter, because the PC's USB port might have not enough power to support the Pi and LCD.

For more info, please check the wiki page.

Anti-Piracy

CAUTION: This product is protected by patent, anyone making copies/knock-offs SHOULD be held liable pursuant to law.

Since the first-generation Raspberry Pi released, Waveshare has been working on designing, developing, and producing various fantastic touch LCDs for the Pi. Unfortunately, there are quite a few pirated/knock-off products in the market. They're usually some poor copies of our early hardware revisions, and comes with none support service.

To avoid becoming a victim of pirated products, please pay attention to the following features when purchasing:

Part Number Resolution LCD Interface Touch Panel Interface For use with Dimension (mm) Touch Panel Type IPS Sound Multi Systems Display Multi Systems Touch Popular Game Consoles
WAVE-102 3.5inch RPi LCD (B) 480×320 I/O I/O Pi As the Pi 3B+ Resistive √ × × × ×
WAVE-103 4inch RPi LCD (A) 480×320 I/O I/O Pi 94 × 61 Resistive √ × × × ×
WAVE-11750 10.1inch HDMI LCD (B) 1280×800 HDMI USB Not only Pi 274 × 187 Capacitive √ × √ √ ×
WAVE-13858 10.1inch HDMI LCD (D) 1280×800 HDMI USB Not only Pi 258 × 177 Capacitive √ √ √ √ ×
WAVE-13859 13.3inch HDMI LCD (H) 1920×1080 HDMI USB Not only Pi 330 × 208 Capacitive √ √ √ √ √

 

Notice for California Residents: Warning symbolWARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov