Interconnects

US$1.24
This is a simple 2x3 male PTH header. This header is in the common configuration for an ISP connector. Each pin has a spacing of 0.1" in between each other.
In stock
+
Add to wish list

US$8.34
This is a simple board that breaks out a female USB type A connector's VCC, GND, D- and D+ pins to a 0.1" pitch header. If you want to add a USB to your project, but don't want to put up with soldering tiny connectors, this is the board for you.
In stock
+
Add to wish list

US$1.95
These 0.1" straight female header strips are commonly used as low-cost connectors for custom-made cables or perforated prototyping PCBs. The standard spacing is the same as on most solderless breadboards and matches 0.1" male header strips.
In stock
+
Add to wish list

US$1.11
These 0.1" female header strips are commonly used as low-cost connectors for custom-made cables or perforated prototyping PCBs. The standard spacing is the same as on most solderless breadboards and matches 0.1" male header strips.
In stock
+
Add to wish list

US$13.13
Its great for connecting things together, soldering to perf-boards, fits into any breadboard, etc. We go through these guys real fast, and thought that given how handy they are, we'd offer them in a pack of ten!
In stock
+
Add to wish list

US$1.95
TRRS connectors are the audio-style connectors that you see on some phones, MP3 players and development boards. TRRS stands for "tip, ring, ring, sleeve," which reflects the fact that, unlike a standard stereo connector, this actually has three conductors and a ground.
In stock
+
Add to wish list

US$1.25

The extra-long pins have a length of 17.1 mm, which is 5.45 mm longer than typical 0.1" straight male header pins. The standard 0.1" spacing allows use with perforated prototyping PCBs and female headers.

Delivery within 2-3 weeks
+
Add to wish list

US$5.17
Go 'cold splice' with these snap-able plastic splices for fast connections. Use with any 19-26 AWG solid core wire and slip them into the plastic splice so that they slide into the metal teeth. Then squeeze down with parallel-jaw or slip joint pliers - don't use needle-noses, they have too much angle and not enough force.
In stock
+
Add to wish list

US$5.17
Go 'cold splice' with these snap-able plastic splices for fast connections. Use with any 22-26 AWG solid core wire and slip them into the plastic splice so that they slide into the metal teeth. Then squeeze down with parallel-jaw or slip joint pliers - don't use needle-noses, they have too much angle and not enough force.
In stock
+
Add to wish list

US$1.25

This is a 24 pin right angle male shrouded box header PC mount for connecting a Female IDS matching IDC ribbon connector.

In stock
+
Add to wish list

US$4.54
This is a 5 position terminal strip. Tin plated lugs and brackets.
Delivery within 2-3 weeks
+
Add to wish list

US$2.65
This is a screw mount non-polarized receptacle with solder tabs. Specifications: Non-Polarized AC Receptacle. 15A current rating. 125V voltage rating. Chassis mount. 

 

Delivery within 2-3 weeks
+
Add to wish list

US$24.50

Operating Voltage: Shield/Earth: 30VAC/60VDC Max. Inner Conductor/Shield: 500VRMS Max. Operating Temperature: -55ºC to +85ºC. Nominal Impedance: 50 Ohms.

In stock
+
Add to wish list

US$10.16
These are 3 pin XLR to 1/4" phono adpators.   Order# Description  T630  3 Pin XLR Female to 1/4" Mono Male...
In stock
+
Add to wish list

US$1.67
Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. These DIY "USB shells" are available in USB A plug, micro B, and USB A socket. 
In stock
+
Add to wish list