Electromechanical

US$1.99
7201-RA-HO Switch, Toggle PCB DPDT 90° Horizontal 6 AMP 125V ON-ON
Delivery within 2-3 weeks
+
Add to wish list

US$8.39
This 3cm x 1.2 cm x 1.5 cm solenoid has a push newton of 5N. Normally pulled in, the entire shaft when extended including the nut equates to 18mm. This device can run from 12-24VDC. The body is an open frame design with no housing or mounting brackets. When powered 24V the shaft will extend and remain until voltage has been shorted, instantaneous extending and retracting. Applications: door projects or interfacing with microcontroller (Arduino). Please make sure to have appropriate power transistors, relays and free wheel diode when connecting solenoid to a circuit.
Delivery within 2-3 weeks
+
Add to wish list

US$1.99
This Piezo transducer module can be used to generate different sounds for robotic projects such as an alarm or proximity detection sound. Requires a sine or square wave drive input signal of 3.3 to 5 volts peak to peak. Comes with a three pin connector and two screw mounting holes for easy assembly into projects.
In stock
+
Add to wish list

US$2.19
This product is a simple micro limit switch. When the lever is pressed, the circuit is closed completing the connection and sending a signal output. These switches are often used to replace worn arcade joystick controls or other mechanical and robotic applications.
In stock
+
Add to wish list

US$44.58
Getting retro vibes? Want to revisit vintage JAMMA games? Have all the components needed (Seimitsu Joysticks, arcade push buttons, micro switches, etc.) except the Xin-Mo board and the wires? Get this kit and you’ll also be able to play with one other friend. Setup your own 2 player hub and start reliving old memories. The board comes with all necessary wiring: Female Lug connector to female connectors and a USB B to USB A cable. It is also compatible with at least three different gaming consoles/platforms: PC, PS3 and Raspberry pie. Note that no soldering is required and that the Xin-Mo supports the configuration of a turbo button. For more information on how to wire each pin refer to the pinout of the Xin-Mo board.
In stock
+
Add to wish list

US$24.95
This is essentially a ramped up version of the Ardumoto motor driver shield but this board is capable of driving a pair of high-current motors! For this monster shield the L298 H-bridge is replaced with a pair of VNH3SP30 full-bridge motor drivers. The VIN and motor out are pitched for our 5mm screw terminals (not included), making it easy to connect larger gauge wires.
In stock
+
Add to wish list

US$7.99
35-3427 Switch, Pushbutton SPST-NO 125V 15A, 250V 10A, Off – (On) Screw lug
In stock
+
Add to wish list

US$12.99
35-3170 Switch, Toggle SPST On – Off Auto-Marine Screw lug
In stock
+
Add to wish list

US$14.49
35-3070 Switch, Toggle SPST On – Off 125V 16A, 250V 8A Screw lug
In stock
+
Add to wish list

US$2.98
35-3030 Switch, Rocker SPST 125V 16A, 250V 10A Red On- Off
In stock
+
Add to wish list

US$11.98
35-990 Switch Lever Snap action Limit QC Tabs 0.250”
In stock
+
Add to wish list

US$5.99
35-865 Switch, Pull chain 125v 6A, 250v 3A, Off 1-On- On
In stock
+
Add to wish list

US$2.98
35-850 Switch, Feed Thru Cord In Line Lamp Wire On Off 125 V 6 A
In stock
+
Add to wish list

US$14.99
35-449 Switch, Pushbutton 90° Panel mount SPST On- Off Eyelets with  screws 125v 6A 250v 3A
Delivery within 2-3 weeks
+
Add to wish list

US$6.99
35-448 Switch, Pushbutton Vert. Panel mount SPST On - Off Eyelets  125v 6A 250v 3A
In stock
+
Add to wish list