Batteries/Chargers/Holders

 

9v 800 mAh lithium USB Rechargeable Battery

Shaped like a normal 9v battery this unit provides approximately 8.2v at full charge and operates like any normal 9v battery cell. The only exception is that this unit is rechargeable! Plug in a micro USB port in the back to charge with your computer, the side indicator will show you the current charge of the unit. Please do take precaution and prevention from wire shortage and paying attention to polarity. Lithium batteries can explode from pressure, heat or voltage short.

More info

 

IMAX B6 LiPro Balance Charger + AC-DC Adapter

It is a very advanced smart charger for your LiPo/LiFe, NiCd and NiMH Batteries, capable of  managing 6S Li-ion/LiPo/LiFe and 15S NiCd/NiMH. The Display and straightforward controls make charging high volatile batteries safe and easy. Simply plug in a 12v DC power source up to a maximum of 5A on the right side and connect your battery with the balance cells (if needed) on the left side.

More info

 

 

 

US$3.63
This is eight "AA" piggyback vertical cell battery holder with a 9 volt snap connection.
Delivery within 2-3 weeks
+
Add to wish list

US$10.42
The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 150mAh for a total of about 0.6 Wh. The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and include the necessary protection circuitry.
In stock
+
Add to wish list

US$2.73
You may be wondering what sets this guy apart from the more common CR2032 coin cell battery, the answer is actually quite important. The CR2025 is actually 0.7mm thinner, than the CR2032, and is only rated at 165mAh. Some applications need a thinner battery to conserve space, and the CR2025 fits the bill.
In stock
+
Add to wish list

US$28.53

This is an excellent choice for anything that requires a small battery with a lot of punch. The voltage is low enough not to tax your regulating circuits, and the discharge rate is high enough to accommodate a lot of electronics and a few small motors. The battery has two cells and outputs 7.4V storing 2200mAh of charge.

Delivery within 2-3 weeks
+
Add to wish list

US$16.33

This is an excellent choice for anything that requires a small battery with a lot of punch. The voltage is low enough not to tax your regulating circuits, and the discharge rate is high enough to accommodate a lot of electronics and a few small motors. The battery has two cells and outputs 7.4V storing 1000mAh of charge.

In stock
+
Add to wish list

US$10.42
Simply plug in the gold plated contacts into any USB port and a 3.7V/4.2V lithium polymer or lithium ion rechargeable battery into the JST plug on the other end. There are two LEDs - one red and one green. While charging, the red LED is lit. When the battery is fully charged and ready for use, the green LED turns on.
In stock
+
Add to wish list

US$7.98

Perfect for portable Arduinos, motors, solenoids, 12V LED strips, etc. An On/Off switch lets you control the power right at the source without unplugging. Batteries not included. Dimensions: 1127mm x 71mm x 19mm (5in x 2.8in x 0.76in). Attached lead + plug is 14cm/6in long. Weight (without batteries): 75g.

In stock
+
Add to wish list

US$5.17
Make a nice portable power pack with this 4 x AA battery holder. It fits any alkaline or rechargeable AA batteries in series. There's a snap on cover and an on/off switch which can be handy when wiring to something without a switch.
In stock
+
Add to wish list

US$6.92
Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches together with 4 machine screws.
Delivery within 2-3 weeks
+
Add to wish list

US$69.13
Need a massive battery for your project? This lithium ion pack is made of 3 balanced 2200mAh cells for a total of 6600mA capacity! The cells are connected in parallel and spot-welded to a protection circuit that provides over-voltage, under-voltage and over-current protection.
In stock
+
Add to wish list

US$8.75
Make a portable power brick with plenty of juice! Use Alkaline AA's for a 9V 3000-4000mAh power supply, or rechargeable NiMH for 2000mAh 7.5V supply. Either one is good for running electronics that have a 5V voltage regulator (thus requiring a 7V+ supply). Will last about 10 times longer than a 9V.
In stock
+
Add to wish list

US$5.25
These are high quality battery clips. They're molded plastic so they wont tear like cheap clips, and they cover the battery terminals to prevent shorts.
In stock
+
Add to wish list

US$19.17
Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 1200mAh for a total of about 4.5 Wh. If you need a larger battery, we also have a 2500mAh+ model (328-ADA). The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and include the necessary protection circuitry. Because they have a genuine JST connector, not a knock-off, the cable wont snag or get stuck in a matching JST jack, they click in and out smoothly.
In stock
+
Add to wish list

US$3.42
Fits any standard AAA battery. When using rechargeable NiMH the output voltage will range from about 3.7V with charged batteries to 2.7V at the end of life with a nominal voltage of 3.6V. When using alkalines, the output will range from 4.6V with new batteries to 3.3V at the end of life with a nominal voltage of about 4.5V
In stock
+
Add to wish list

US$27.92
Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 2500mAh for a total of about 10 Wh. If you need a smaller battery, we also have a 1200mAh model (258-ADA).
In stock
+
Add to wish list