Perfect for portable Arduinos, motors, solenoids, 12V LED strips, etc. An On/Off switch lets you control the power right at the source without unplugging. Batteries not included. Dimensions: 1127mm x 71mm x 19mm (5in x 2.8in x 0.76in). Attached lead + plug is 14cm/6in long. Weight (without batteries): 75g.
The product kit comes with: A fully tested and assembled LED backpack. Ultra-bright 4-digit 0.56" tall red seven-segment display. 4-pin header. A bit of soldering is required to attach the matrix onto the backpack but its very easy to do and only takes about 5 minutes.
The product kit comes with: A fully tested and assembled LED backpack. Ultra-bright 8x8 yellow matrix. 4-pin header. A bit of soldering is required to attach the matrix onto the backpack but its very easy to do and only takes about 5 minutes.Â
The product kit comes with: A fully tested and assembled 1.2" LED backpack. Ultra-bright 1.2" 8x8 red matrix. 4-pin header. A bit of soldering is required to attach the matrix onto the backpack but its very easy to do and only takes about 5 minutes.
The product kit comes with: A fully tested and assembled 1.2" LED backpack. Ultra-bright 1.2" 8x8 green matrix. 4-pin header. A bit of soldering is required to attach the matrix onto the backpack but its very easy to do and only takes about 5 minutes.
The product kit comes with: A fully tested and assembled 1.2" LED backpack. Ultra-bright 1.2" 8x8 blue matrix. 4-pin header. A bit of soldering is required to attach the matrix onto the backpack but its very easy to do and only takes about 5 minutes.
The product kit comes with: A fully tested and assembled 1.2" LED backpack. Ultra-bright 1.2" 8x8 yellow/orange matrix. 4-pin header. A bit of soldering is required to attach the matrix onto the backpack but its very easy to do and only takes about 5 minutes.
Build a custom USB gamepad that has an accelerometer mouse inside! This project pack comes with: SNES controller, Teensy, Accelerometer, 5' mini-B USB cable, 8" of ribbon cable, 2 squares of foam tape.Â
15 rows of double 5-hole rows + 48 individual holes. 2 power rails with positive/negative markings. 2.1" x 1.3" (54mm x 33mm), 0.063" thick FR4. 1.2mm / 0.047" drill holes. 4 x 0.125"/3mm drill mounting holes spaced on a 45.5mm x 25.4mm / 1.8" x 1" rectangle.
The product kit comes with: A fully tested and assembled LED backpack. Ultra-bright 4-digit 0.56" tall blue seven-segment display. 4-pin header. A bit of soldering is required to attach the matrix onto the backpack but its very easy to do and only takes about 5 minutes.
The product kit comes with: A fully tested and assembled LED backpack. Ultra-bright 4-digit 0.56" tall green seven-segment display. 4-pin header. A bit of soldering is required to attach the matrix onto the backpack but its very easy to do and only takes about 5 minutes.Â
Includes encapsulated laser diodes that are Class IIIa 5mW, with a 650nm red wavelength. They can be driven from 2.8V to 5.2V so they're great for your embedded electronics project.
We're carrying this adapter primarily to allow Chumby Hacker Board users to adapt our nice 5V @ 2A power supply to their CHB. But you can use this adapter for anything else that has a 1.7mm DC jack, such as a PSP.
This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 3.7W channels into 3 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC.
