Sparkfun

1 2 3 4 5 6 7 8
2 - 16
US$1.99
This is a simple three wire cable. Great for jumping from board to board or just about anything else. There is a 3-pin Molex connector with 0.1" spacing on one end, bare cable on the opposite end. It also comes with the mating connector for the Molex. Dimensions: 6" length.
Delivery within 1-2 weeks
+
Add to wish list

US$29.95
The SparkFun ESP32 Thing Plus is the next step to get started with Espressif IoT ideations while still enjoying all the amenities of the original ESP32 Thing. Espressif's ESP32 WROOM is a powerful WiFi and Bluetooth MCU module that targets a wide variety of applications. At the core of this module is the ESP32-D0WDQ6 chip which is designed to be both scalable and adaptive.
Delivery within 1-2 weeks
+
Add to wish list

US$26.95
The SparkFun weather:bit is a fully loaded "carrier" board for the micro:bit that, when combined with the micro:bit, provides you with a fully functional weather station. With the weather:bit you will have access to barometric pressure, relative humidity and temperature readings. There are also connections on this carrier board to optional sensors such as wind speed, direction, rain gauge and soil readings!
In stock
+
Add to wish list

US$5.45
The SparkFun Qwiic Shield for Arduino Nano provides you with a quick and easy way to enter into SparkFun's Qwiic ecosystem with your Arduino Nano board. The Qwiic shield connects the I2C bus (GND, 3.3V, SDA and SCL) on your Arduino Nano to four SparkFun Qwiic connectors (two horizontally and two vertically mounted). The Qwiic connect system allows for easy daisy chaining so long as your devices are on different addresses, you can connect as many Qwiic devices as you would like.
In stock
+
Add to wish list

US$10.45
The Qwiic Button with built-in red LED simplifies all of those nasty worries away into an easy to use I2C device! Utilizing our Qwiic Connect System, using the button is as simple as connecting a cable and loading up some pre-written code!
In stock
+
Add to wish list

US$8.95
The SparkFun Qwiic pHAT V2.0 for Raspberry Pi provides you with the quickest and easiest way to enter into SparkFun’s Qwiic ecosystem while still using that Raspberry Pi that you’ve come to know and love. The Qwiic pHAT connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Raspberry Pi to an array of Qwiic connectors on the HAT.
In stock
+
Add to wish list

US$44.73

SEN-13261 OpenScale Weight and Temperature Sensor

This is a OpenScale from “SparkFun” is a simple-to-use, open source solution for measuring weight and temperature. It has the ability to read multiple types of load cells and offers a simple-to-use serial menu to configure calibration value, sample rate, time stamp and units of precision.

In stock
+
Add to wish list

US$1.99
The SparkFun Qwiic SHIM for Raspberry Pi is a small, easily removable breakout that easily adds a Qwiic connector to your Raspberry Pi. The SHIM design allows you to plug directly to the Pi's I2C bus with no soldering required and the thin PCB design allows for it to be sandwiched on your Pi GPIO with other HATs!
In stock
+
Add to wish list

US$19.95
The SparkFun Qwiic TMP117 breakout is a high precision temperature sensor equipped with an I2C interface. It outputs temperature readings with high precision of ±0.1°C across the temperature range of -20°C to +50°Cs with no calibration and a maximum range from -55°C to 150°C.
In stock
+
Add to wish list

US$2.29
This is a jumper adapter cable that comes pre-terminated with a female Qwiic JST connector on one end and a breadboard hookup pigtail on the other. This cable makes it easy to connect components with a Qwiic connector to a breadboard or an Arduino-based device’s pins.
Delivery within 1-2 weeks
+
Add to wish list

US$11.95
The SparkFun Qwiic Cable Kit includes 10 cables of various lengths and styles that will get your Qwiic boards connected together, to a development platform, or to a breadboard. Each Qwiic Cable's wires have been color coded to red, black, blue and yellow with 1mm JST termination.
Delivery within 1-2 weeks
+
Add to wish list

US$6.99
The SparkX ATECC608A Cryptographic Co-processor Breakout allows you to add strong security to your IoT node, edge device, or embedded system. This includes asymmetric authentication, symmetric AES-128 encryption/decryption, and much more. Note, the ATECC608A has limited Arduino support and the complete datasheet is under NDA with Microchip.
In stock
+
Add to wish list

US$34.95
If you’re ready to step up your Arduino game from older 8-bit/16MHz microcontrollers, the SparkFun RedBoard Turbo is a formidable alternative. At its heart, the RedBoard Turbo uses the ATSAMD21G18, which is an ARM Cortex M0+, 32-bit microcontroller that can run at up to 48MHz. With an impressive 4MB of external flash memory and a UF2 (USB Flashing Format) bootloader, the RedBoard Turbo provides you with an economical and easy to use development platform if you're needing more power than the classic RedBoard.
In stock
+
Add to wish list

US$84.95
The Qwiic Pro kit provides you with a RedBoard Turbo, two sensors, two accessory boards, and all the cables you need to start utilizing Qwiic and I2C easily. This kit was designed to allow users to get started with Arduino without the need for soldering or breadboarding. Hooking up a handful of inputs and outputs to a RedBoard has never been so easy. Use the joystick, accelerometer, or proximity sensor, and one small display for outputting text, graphics, or even a microPong game!
In stock
+
Add to wish list

US$6.99
The SparkFun Fuse Breakout Kit comes with everything you need to assembly & use a glass capsule, inline fuse (ferrule type) for your project. The simple breakout design allows for a barrel jack and the option for a screw terminal to be used for (VIN) power input and a second screw terminal used for VOUT. Any 5mm x 20mm glass capsule fuse can be used with this kit depending on your project needs but we have been sure to include a 250VAC, 500mA one to get you started.
In stock
+
Add to wish list
1 2 3 4 5 6 7 8
2 - 16