Our Brands

Sparkfun

26 - 40
34 35 36 37 38 39 40 41 42 43 44 45 46
Newest Items First
15 Per Page
WRL-10534 RF Link Transmitter - 434 MHz
WRL-10534 RF Link Transmitter - 434 MHz
CA$8.05
This is a wireless transmitter to work with our 434MHz receiver. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link.
In stock
+ −
Add to wish list
WRL-10532 RF Link Receiver - 4800 bps (434 MHz)
WRL-10532 RF Link Receiver - 4800 bps (434 MHz)
CA$10.18
This is a wireless receiver to work with our 434MHz transmitter. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link.
In stock
+ −
Add to wish list
WRL-00145 Duck Antenna RP-SMA 2.4 GHz
WRL-00145 Duck Antenna RP-SMA 2.4 GHz
CA$12.23
This is a 2.4GHz Duck Antenna 2.2dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. 4" long.
In stock
+ −
Add to wish list
WRL-00558 Duck Antenna RP-SMA - Large 2.4 GHz
WRL-00558 Duck Antenna RP-SMA - Large 2.4 GHz
CA$15.31
This is a 2.4GHz Large Duck Antenna 5dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance.
In stock
+ −
Add to wish list
WRL-09143 Duck Antenna RP-SMA 900 MHz
WRL-09143 Duck Antenna RP-SMA 900 MHz
CA$13.14
This is a 900 - 1800 MHz Duck Antenna 2dBi with regular Reverse Polarized -SMA RF connector. Perfect for use with the XBee 900MHz units. 50 ohm impedance. 105mm long.
In stock
+ −
Add to wish list
WRL-00662 Interface Cable RP-SMA to U.FL
WRL-00662 Interface Cable RP-SMA to U.FL
CA$7.62
Cable interfaces UFL RF connectors to RP-SMA antennas. Use it to attach any standard RP-SMA 2.4GHz antenna to the DPAC 802.11 modules. Dimensions: 4" Length.
In stock
+ −
Add to wish list
WRL-09145 Interface Cable SMA to U.FL
WRL-09145 Interface Cable SMA to U.FL
CA$7.62
This is a 4" connector cable that interfaces U.FL RF connectors to regular SMA connections.
In stock
+ −
Add to wish list
DEV-08822 Coin Cell Holder - Sewable SMD
DEV-08822 Coin Cell Holder - Sewable SMD
CA$2.76
This is a coin cell holder for the common CR2032 type battery. The holder has a neat pop-in, pop-out feature that makes changing the battery easy. The feet of the holder have a small hole that allow it to be sewn without modification.
In stock
+ −
Add to wish list
SEN-00251 Thermocouple Type-K Glass Braid Insulated
SEN-00251 Thermocouple Type-K Glass Braid Insulated
CA$28.71
This is a 36" high temperature Type-K Thermocouple with glass braid insulation. Features: Type-K Thermocouple (Ni-Cr). 30 gauge stripped and prepped wires. Thermocouple range : -270 to +1372C (-454 to +2501F). Glass braid insulation range : -73 to +482C(-100 to +900F). Yellow + / Red -. 
In stock
+ −
Add to wish list
SEN-10239 Humidity Sensor - HH10D
SEN-10239 Humidity Sensor - HH10D
CA$16.85
This is a relative humidity sensor module comprised of a capacitive type humidity sensor, a CMOS capacitor to frequency converter and an EEPROM used to hold the calibration factors. Due to the characteristics of capacitor type humidity sensor, the system can respond to humidity change very quickly.
In stock
+ −
Add to wish list
BOB-08688 TEMT6000 Breakout Board
BOB-08688 TEMT6000 Breakout Board
CA$7.85
This is a breakout board for the TEMT6000 Ambient Light Sensor. Only what you need, nothing you don't. Sensor acts like a transistor - the greater the incoming light, the higher the analog voltage on the signal pin.
In stock
+ −
Add to wish list
US1881 - Hall Effect Sensor
US1881 - Hall Effect Sensor
CA$2.30
This is an integrated Hall effect latched sensor. Holding a magnet near the sensor will cause the output pin to toggle. This makes for a robust presence sensor.
In stock
+ −
Add to wish list
SEN-00241 Infrared Emitters and Detectors
SEN-00241 Infrared Emitters and Detectors
CA$3.00
Side-looking Infrared Emitters and IR Detectors. These simple devices operate at 940nm and work well for generic IR systems including remote control and touch-less object sensing.
In stock
+ −
Add to wish list
SEN-08733 Infrared Sensor Jumper wire - 3-pin JST
SEN-08733 Infrared Sensor Jumper wire - 3-pin JST
CA$2.31
This is a 3-pin JST connector with red, black, and yellow wire colors cut to a length of 5 inch out. This cable comes fully assembled as shown and connects directly to many different Sharp sensors. Quick and easy, this cable will save you 15-20 minutes over making your own wiring harness.
In stock
+ −
Add to wish list
BOB-09322 Breakout Board for Photo Interrupter GP1A57HRJ00F
BOB-09322 Breakout Board for Photo Interrupter GP1A57HRJ00F
CA$3.07
A simple breakout PCB for the GP1A57HR photo interrupter. This PCB has three connections for PWR, GND, and Signal. When the gate is clear, SIG will be high (>4.9V). When the gate is blocked by a finger, writing utensil, food pellet, or anything else - SIG will go low (<0.4V).
In stock
+ −
Add to wish list
26 - 40
34 35 36 37 38 39 40 41 42 43 44 45 46