Adafruit

1 2 3 4 5 6 7 8 9 10 11 12
6 - 20
US$9.05

The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. Inside the big USB plug is a USB<->Serial conversion chip and at the end of the 36" cable are four wire - red power, black ground, white RX into USB port, and green TX out of the USB port. The power pin provides the 5V @ 500mA direct from the USB port and the RX/TX pins are 3.3V level for interfacing with the most common 3.3V logic level chipsets.

In stock
+
Add to wish list

US$27.92
At the Feather HUZZAH's heart is an ESP8266 WiFi microcontroller clocked at 80 MHz and at 3.3V logic. This microcontroller contains a Tensilica chip core as well as a full WiFi stack. You can progam the microcontroller using the Arduino IDE for an easy-to-run Internet of Things core.
In stock
+
Add to wish list

US$13.13

This breakout board has a microSD card slot for providing extra storage memory when required.

In stock
+
Add to wish list

US$19.25
This touch-able add on shield for Arduinos will inspire your next interactive project with 12 capacitive touch sensors.
In stock
+
Add to wish list

US$12.17
Finally, a way to get up to 8 same-address I2C devices hooked up to one microcontroller - this multiplexer acts as a gatekeeper, shuttling the commands to the selected set of I2C pins with your command.
Delivery within 2-3 weeks
+
Add to wish list

US$1.32
977 Adafruit TO-220 Clip-On Heatsink Get the most out of your regulators, transistors and other TO-220 packaged chips by clipping on a heat-sink. Your...
In stock
+
Add to wish list

US$19.25
This is a Lithium Ion and Lithium Polymer battery charger based on the MCP73833 device. It uses a USB mini-B for connection to any computer or 'USB wall adapter'. Charging is performed in three stages: first a preconditioning charge, then a constant-current fast charge and finally a constant-voltage trickle charge to keep the battery topped-up.
In stock
+
Add to wish list

US$53.68
This lovely little shield is the best way to add a small, colorful and bright display to any project. We took our popular 1.8" TFT breakout board and remixed it into an Arduino shield complete with microSD card slot and a 5-way joystick navigation switch (with a nice plastic knob)!
In stock
+
Add to wish list

US$19.17
Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 1200mAh for a total of about 4.5 Wh. If you need a larger battery, we also have a 2500mAh+ model (328-ADA). The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and include the necessary protection circuitry. Because they have a genuine JST connector, not a knock-off, the cable wont snag or get stuck in a matching JST jack, they click in and out smoothly.
In stock
+
Add to wish list

US$27.92
Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 2500mAh for a total of about 10 Wh. If you need a smaller battery, we also have a 1200mAh model (258-ADA).
In stock
+
Add to wish list

US$26.17

This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 3.7W channels into 3 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC.

Delivery within 2-3 weeks
+
Add to wish list

US$13.13
This is a nice way to add a small-distance proximity sensor to your microcontroller project.
Delivery within 2-3 weeks
+
Add to wish list

US$23.02
The FLORA is small (1.75" diameter, weighing 4.4 grams). The FLORA family also has the best stainless steel threads, sensors, GPS modules and chainable LED NeoPixels, perfect accessories for the FLORA main board. The FLORA has built-in USB support. Built in USB means you plug it in to program it, it just shows up - all you need is a Micro-B USB cable, no additional purchases are needed!
In stock
+
Add to wish list

US$8.67
This breakout PCB set will make your life much much easier and get you prototyping faster than ever. One side has a 12-TSSOP pin out with traces going to two rows of 0.1" spaced holes, the other has 12-SOIC. Solder your chip to either side and you're ready to rock on any solderless breadboard.
Delivery within 2-3 weeks
+
Add to wish list

US$69.30
It features a 3.5" display with 480x320 16-bit color pixels and a resistive touch overlay just like our popular original, but this one is engineered specifically to work with the newer "2x20 connector" Raspberry Pi's. The plate uses the high speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all it plugs right in on top!
Delivery within 2-3 weeks
+
Add to wish list
1 2 3 4 5 6 7 8 9 10 11 12
6 - 20