Adafruit

1 2 3 4 5 6 7 8 9 10 11
5 - 19
US$2.49
If you need to connect a DC power wall wart to a board that doesn't have a DC jack - this adapter will come in very handy! There is a 2.1mm DC jack on one end, and a screw terminal block on the other.
In stock
+
Add to wish list

US$2.49
If you need to connect a battery pack or wired power supply to a board that has a DC jack - this adapter will come in very handy! There is a 2.1mm DC plug on one end, and a screw terminal block on the other.
In stock
+
Add to wish list

US$2.49
These 3-wire cables are 163mm (6.4") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 3 wires you want to be able to plug and unplug.
In stock
+
Add to wish list

US$2.49
This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" female sockets on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them.
In stock
+
Add to wish list

US$2.50
The 5384-ADA is a 300mm 4 wire connector. It is fitted with JST-SH and has a solid latch that makes it easier to insert.
 
In stock
+
Add to wish list

US$2.53
This 1.5" diameter speaker cone is the perfect addition to any audio project where you need an 8Ω impedance and are using 0.25W or less of power. We particularly like this cone as it's very simple and its plastic body is extremely lightweight and thin.
In stock
+
Add to wish list

US$2.53
This is great in conjunction with any 16-pin IDC cables. It comes in two parts, a 'pin-through' socket and a male header. The socket straddles the center of a breadboard or Perma-Proto and then header plugs into the top of the socket.
In stock
+
Add to wish list

US$2.63
Piezo Speakers are used for making beeps, tones and alerts. This one is petite but loud! Drive it with 3-30V peak-to-peak square wave.
In stock
+
Add to wish list

US$2.63
These 4-wire cables are 15cm long and come as a set, one side has a JST SM type connector plug on the end. The other side has a matching JST SM type receptacle connector.
In stock
+
Add to wish list

US$2.63
The 74LVC245 is designed so that even when it runs at 1.8V, it still happily accepts 5V signals in one pin and converts it to a lower logic level on the opposite pin. This chip is only for digital signals, it doesn't convert analog signals (you need an op amp for that).
Delivery within 1-2 weeks
+
Add to wish list

US$2.63
This electret capsule microphone is the same one we use in our great microphone amplifier board. It contains a small vibrating element that will output a few milllivolts peak-to-peak.
In stock
+
Add to wish list

US$2.63
You have some electrons over here, and you want them over there but you don't want the electrons from over there to be able to come over here? That's what a diode is for, these are directional current valves and have the benefit of being waaay smaller than vacuum tubes. 
In stock
+
Add to wish list

US$2.63
Repair or design your very own audio cables with these nice and durable phono-jack connectors. This is a great plug to make your own cable with. it's made out of durable metal with a flexible, sturdy spring for strain-relief.
In stock
+
Add to wish list

US$2.63
Connect your own PCB to a Raspberry Pi B+ with this normal-height female header.
In stock
+
Add to wish list

US$2.63
One truth about working with A/V is you always need the cable or adapter you don't have in your toolbox. That's why we love these terminal-block RCA connectors so much. No soldering required! Use stranded or solid core wire and a small screw driver to create custom wiring jigs.
In stock
+
Add to wish list
1 2 3 4 5 6 7 8 9 10 11
5 - 19