Our Brands

Adafruit

9 - 23
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
25 - 39
Sort by Price: Low to High
15 Per Page
916-ADA Waterproof Metal On/Off Switch with Red LED Ring - 16mm Red On/Off
916-ADA Waterproof Metal On/Off Switch with Red LED Ring - 16mm Red On/Off
US$10.42
This button is an on/off switch button, when you press it the 'normally-open' contact shorts to the common contact and the button stays 'pressed'. When you press it a second time, the button springs open, and the contacts open up again. 
In stock
+ −
Add to wish list
1304-Ada Micro Lipo - USB LiIon/LiPoly charger
1304-Ada Micro Lipo - USB LiIon/LiPoly charger
US$10.42
Simply plug in the gold plated contacts into any USB port and a 3.7V/4.2V lithium polymer or lithium ion rechargeable battery into the JST plug on the other end. There are two LEDs - one red and one green. While charging, the red LED is lit. When the battery is fully charged and ready for use, the green LED turns on.
In stock
+ −
Add to wish list
1365-ADA Acrylic Stand for 16x2 Character LCD
1365-ADA Acrylic Stand for 16x2 Character LCD
US$10.42
Made of 3mm black acrylic pieces, with 4 x 1" nylon screws & 4 x nylon hex nuts, it goes together in a jiffy and looks super-spiffy!
In stock
+ −
Add to wish list
1375-ADA Standalone Toggle Capacitive Touch Sensor Breakout
1375-ADA Standalone Toggle Capacitive Touch Sensor Breakout
US$10.42
This is the simplest way to create a project with a single "toggle" capacitive touch sensor. No microcontroller is required here - just power with 1.8 to 5.5VDC and touch the pad to activate the sensor.
In stock
+ −
Add to wish list
1426-ADA NeoPixel Stick - 8 x WS2812 5050 RGB LED with Integrated Drivers
1426-ADA NeoPixel Stick - 8 x WS2812 5050 RGB LED with Integrated Drivers
US$10.42
We crammed 8 of the tiny 5050 (5mm x 5mm) smart RGB LEDs onto a PCB with mounting holes and a chainable design. Use only one microcontroller pin to control as many as you can chain together!
In stock
+ −
Add to wish list
1317-ADA Lithium Ion Polymer Battery - 3.7v 150mAh
1317-ADA 3.7v 150mAh Lithium Ion Polymer Battery
US$10.42
The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 150mAh for a total of about 0.6 Wh. The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and include the necessary protection circuitry.
In stock
+ −
Add to wish list
2226-ADA NeoPixel Jewel - 7 x WS2812 5050 RGB LED with Integrated Drivers
US$10.42
We fit seven of our the tiny 5050 (5mm x 5mm) smart RGB LEDs onto a beautiful, round PCB with mounting holes and a chainable design to create what we think is our most elegant (and evening-wear appropriate) NeoPixel board yet.
Delivery within 2-3 weeks
+ −
Add to wish list
2173-ADA 8mm Chromed Metal Wide Bevel LED Holder - Pack of 5
US$10.42
These are handy for projects using individual LEDs as they look sleek, and your LED won't budge.
In stock
+ −
Add to wish list
2144-ADA Flex Cable for Raspberry Pi Camera - 2 meters
US$10.42
This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size.
Delivery within 2-3 weeks
+ −
Add to wish list
2946-ADA Adafruit 16x9 Charlieplexed PWM LED Matrix Driver - IS31FL3731
US$10.42
The IS31FL3731 will let you get back to that classic LED matrix look, with a nice upgrade! This I2C LED driver chip has the ability to PWM each individual LED in a 16x9 grid so you can have beautiful LED lighting effects, without a lot of pin twiddling. Simply tell the chip which LED on the grid you want lit, and what brightness and it's all taken care of for you.
In stock
+ −
Add to wish list
482-ADA Rugged Metal On/Off Switch with Green LED Ring - 16mm Green On/Off
US$10.42
These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal actuator, surrounded by a green plastic LED ring. On the back there are 3 contacts for the button (common, normally-open and normally-closed) and 2 for the green LED ring (+ and -). Connect 3 to 6V to the LED to have it light up nicely, there's a built in resistor! If you want to use this with a higher voltage, say 12V or 24V, simply add a 470 ohm resistor in series with the LED connection to keep the LED current at around 20mA.
In stock
+ −
Add to wish list
Adafruit Sensirion SHTC3 Temperature & Humidity Sensor - STEMMA QT / Qwiic
US$10.45
Sensirion Temperature/Humidity sensors are some of the finest & highest-accuracy devices you can get. And finally, we have some that have a true I2C interface for easy reading. The SHTC3 sensor has an excellent ±2% relative humidity and ±0.2 °C accuracy for most uses. Unlike some earlier SHT sensors, this sensor has a true I2C interface on address 0x70.
In stock
+ −
Add to wish list
Adafruit LPS22 Pressure Sensor - STEMMA QT / Qwiic - LPS22HB
US$10.45
This absolute pressure sensor, ST LPS22HB (a.k.a LPS22) can quickly and easily measure this air pressure, useful when you want to know about the weather (are we in a low-pressure or high-pressure system?) or to determine altitude, as the air thins out the higher we get above sea level.
In stock
+ −
Add to wish list
153 Breadboarding wire bundle
153 Breadboarding wire bundle
US$10.50
65 flexible stranded core wires with stiff ends molded on in red, orange, yellow, green, blue, brown, black and white. These are a major improvement over the "box of bent wires" that are sometimes sold with breadboards, and faster than stripping your own solid core wires. Makes breadboarding super fast.
In stock
+ −
Add to wish list
641 Stainless Medium Conductive Thread - 3 ply - 18 meter/60 ft
641 Stainless Medium Conductive Thread - 3 ply - 18 meter/60 ft
US$10.71
This thread is 3 ply, thicker than every day polyester or cotton thread but still thin enough to be sewn by hand in medium-eye needles. This may be sew-able by a sewing machine that can handle 'heavy' thread. Because it is strong and smooth, its ideal for any wearable/e-textile project.
In stock
+ −
Add to wish list
9 - 23
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
25 - 39