Our Brands

Adafruit

1 2 3 4 5 6 7 8 9 10 11
5 - 19
Newest Items First
32 Per Page
JST PH 3-pin Plug to Color Coded Alligator Clips Cable
US$2.99
This cable has a JST PH 3-pin on one side and alligator clips on the other, so it could be used to connect to wires or pads like that on the Circuit Playground or micro:bit.
In stock
+ −
Add to wish list
FTDI Serial TTL-232 USB Type C Cable - 3V Power and Logic
US$30.73
This is a USB C to TTL serial cable with an FTDI FT232R usb/serial chip embedded in the head. It has a 6-pin socket at the end with 5V power and ground, as well as RX, TX, RTS and CTS at 3V logic levels. Useful whenever you want to communicate with a TTL serial device such as an Arduino Pro Mini or ESP breakout, and the pinout will match up exactly to any 'FTDI' 6-pin header.
Delivery within 2-3 weeks
+ −
Add to wish list
Assembled DC Motor + Stepper FeatherWing Add-on
US$32.60
This is the Fully assembled (with headers) DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors). Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top or bottom of your Feather board and let the board take flight!
In stock
+ −
Add to wish list
Adafruit Feather M0 with RFM95 LoRa Radio - 900MHz - RadioFruit
US$48.91
This is the Adafruit Feather M0 RFM95 LoRa Radio (900MHz). We call these RadioFruits, our take on an microcontroller with a "Long Range (LoRa)" packet radio transceiver with built in USB and battery charging. Its an Adafruit Feather M0 with a 900MHz radio module cooked in! Great for making wireless networks that are more flexible than Bluetooth LE and without the high power requirements of WiFi.
Delivery within 2-3 weeks
+ −
Add to wish list
Adafruit PDM Microphone Breakout with JST SH Connector
US$7.63
The first thing to note is that this sensor does not provide an 'analog' output like many of our electret microphone assemblies. So it's great for chips that do not have analog inputs. Secondly, the digital interface is a very simplistic pulse density modulation output. It's digital but its notPWM and it's not I2S. You will need to make sure your chip has a PDM interface - most 32-bit processors these days do!
In stock
+ −
Add to wish list
Adafruit Perma-Proto 40-Pin Raspberry Pi Breadboard PCB Kit - with 2x20 Header
US$12.25
It has the Cobbler baked right in. Simply solder the 2x20 box header in, and you get all the labeled breakouts with tons of prototyping space, power rails, mounting holes and that gorgeous silk. This version is for modern Raspberry Pi computers with 2x20 connectors such as the Pi B+, A+, 2, 3, 4, Zero, etc!
In stock
+ −
Add to wish list
Adafruit Perma-Proto 40-Pin Raspberry Pi Half-Size PCB Kit - with 2x20 Header
US$9.17
This product has the Cobbler baked right in. Simply solder the 2x20 box header in, and you get all the labeled breakouts with extra prototyping space, power rails, mounting holes and that gorgeous silk. This version is for modern Raspberry Pi computers with 2x20 connectors such as the Pi B+, A+, 2, 3, 4, Zero, etc!
In stock
+ −
Add to wish list
Adafruit AirLift FeatherWing – ESP32 WiFi Co-Processor
US$19.95
Give your Feather project a lift with the Adafruit AirLift FeatherWing - a FeatherWing that lets you use the powerful ESP32 as a WiFi co-processor. You probably have your favorite Feather (like the Feather M4) that comes with its own set of awesome peripherals and lots of libraries. But it doesn't have WiFi built in! So lets give that chip a best friend, the ESP32. This chip can handle all the heavy lifting of connecting to a WiFi network and transferring data from a site, even if its using the latest TLS/SSL encryption (it has root certificates pre-burned in).
Delivery within 2-3 weeks
+ −
Add to wish list
USB C to USB C Cable - USB 3.1 Gen 4 with E-Mark - 1 meter long
US$16.97
As technology changes and adapts, so does Adafruit! Rather than the regular USB A, this cable has USB C to USB C plugs! USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us has inserted USB correctly the first time? Works great with any device that has a USB C port.
In stock
+ −
Add to wish list
Adafruit MCP9600 I2C Thermocouple Amplifier - K, J, T, N, S, E, B and R Type T
US$22.34
Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. The Adafruit MCP9600 does all that for you, and can be easily interfaced with any microcontroller or single-board-computer with I2C. Inside, the chip handles all the analog stuff for you, and can interface with just about any thermocouple type: K, J, T, N, S, E, B and R type are all supported! You can also set various alerts for over/under temperature, and read the thermocouple (hot) temperature and the chip (cold) temperature. All this over common I2C.
In stock
+ −
Add to wish list
Adafruit Prop-Maker FeatherWing
US$15.33
The Adafruit Feather series gives you lots of options for a small, portable, rechargeable microcontroller board. Perfect for fitting into your next prop build! This FeatherWing will unlock the prop-maker inside all of us, with tons of stuff packed in to make sabers & swords, props, toys, cosplay pieces, and more. We looked at hundreds of prop builds, and thought about what would make for a great low-cost (but well-designed) add-on for our Feather boards.
Delivery within 2-3 weeks
+ −
Add to wish list
Assembled Adafruit Prop-Maker FeatherWing
US$16.73
The Adafruit Feather series gives you lots of options for a small, portable, rechargeable microcontroller board. Perfect for fitting into your next prop build! This FeatherWing will unlock the prop-maker inside all of us, with tons of stuff packed in to make sabers & swords, props, toys, cosplay pieces, and more. This version of the FeatherWing has plain headers soldered in, so it's easy to plug into our Feathers. We looked at hundreds of prop builds, and thought about what would make for a great low-cost (but well-designed) add-on for our Feather boards.
In stock
+ −
Add to wish list
Adafruit Quad Side-By-Side FeatherWing Kit with Headers
US$15.33
This is the FeatherWing Quad Side-by-Side - a prototyping add-on and more for all Feather boards. This is similar to our FeatherWing Proto (2884-ADA) except there are four! The magic of the Quad comes when you want to connect your Feather to three other Feather Wings without needing any stacking headers! The Quad comes with: 1 Quad Side-by-side Wing PCB, 4 sets Feather Female Headers.
In stock
+ −
Add to wish list
Adafruit Quad 2x2 FeatherWing Kit with Headers
US$15.33
This is the FeatherWing Quad 2x2 - a prototyping add-on and more for all Feather boards. This is similar to our FeatherWing Proto (2884-ADA) except there are four! The magic of the Quad comes when you want to connect your Feather to three other Feather Wings without needing any stacking headers. The boards are all set up in a 2x2 grid, thus the name The Quad comes with: 1 Quad 2x2 Wing PCB, 4 sets Feather Female Headers.
In stock
+ −
Add to wish list
2.13" Flexible Monochrome eInk / ePaper Display - 212x104 Monochrome
US$26.95
This display is true E-Ink / E-Paper, once an image is displayed it will stay even once you remove all power. The image is also high contrast and very daylight readable. It really does look just like printed paper! This flexible display sports a 2.13" monochrome (black and white) display. It has 212x104 black ink pixels on a white-ish background. This is the same resolution as the 2.13" Tri-Color display, but doesn't have a red ink layer. The monochrome displays also take a lot less time to update, only a couple seconds instead of 15 seconds.
In stock
+ −
Add to wish list
Adafruit INA260 High or Low Side Voltage, Current, Power Sensor
US$16.15
This breakout board may well be the last current sensing solution you ever need to buy. Not only can it do the work of two multimeters, but it can do it with amazing precision and flexibility. With it you can measure high or low side DC current, the bus voltage, and have it automatically calculate the power. It can do so over impressive voltage, current, and temperature ranges with better than 1% accuracy, all while delivering the data in an easy to use format over I2C.
Delivery within 2-3 weeks
+ −
Add to wish list
Adafruit HUZZAH32 – ESP32 Breakout Board
US$19.06
This breakout is basically the 'big sister' of our HUZZAH 8266, but instead of an ESP8266 it has the '32! We've pared down our popular Feather ESP32, removing the battery charger and USB-serial converter. You just get a regulator, some protection diodes, two buttons and an LED. For some projects, where price and size are at a premium, you can program this board over the 'FTDI cable' breakout when needed, and leave it alone otherwise.
Delivery within 2-3 weeks
+ −
Add to wish list
Adafruit TPL5110 Low Power Timer Breakout
US$7.63
The Adafruit TPL5110 Power Timer is a stand-alone breakout that will turn any electronics into low-power electronics! It will take care of turning your project on/off using a built in timer that can vary from once every 100ms up to once every two hours. Basically, the TPL will turn on periodically, adjustable by potentiometer or resistor, and turn on your project's power. It will then wait until a signal is received from the project to tell the TPL that it can safely turn off the power. If the TPL does not receive a signal by the set time-out, it will reset the device like a watchdog timer.
In stock
+ −
Add to wish list
Adafruit TPL5111 Low Power Timer Breakout
US$9.17
The Adafruit TPL5111 Low Power Reset Timer is a stand-alone breakout that will turn any electronics into low-power electronics! It will take care of enabling & disabling your electronics using a built in timer that can vary from once-every 100ms up to once every two hours. Basically, the TPL will set an enable pin high periodically, adjustable by potentiometer or resistor, and turn on your project's power. It will then wait until a signal is received from the project to tell the TPL that it can safely disable the project by setting the enable pin low. If the TPL does not receive a signal by the set time-out, it will reset the device like a watchdog timer.
In stock
+ −
Add to wish list
TV-B-Gone Kit - Universal v1.2
US$29.95
The TV-B-Gone is a kit that, when soldered together, allows you to turn off almost any television within 150 feet or more.  It works on over 230 total power codes - 115 American/Asian and another 115 European codes.  You can select which zone you want during kit assembly. This is an unassembled kit which means that soldering is required - but it’s very easy and a great introduction to soldering in general.  The kit’s powered by 2x AA batteries - that aren’t included - and the output comes from 2x narrow beam IR LEDs and 2x wide-beam IR LEDs.
In stock
+ −
Add to wish list
ADXL343 - Triple-Axis Accelerometer (+-2g/4g/8g/16g) w/ I2C/SPI
US$9.17
Analog Devices has followed up on their popular classic, the ADXL345, with this near-drop-in-replacement, the ADXL343. Like the original, this is a triple-axis accelerometer with digital I2C and SPI interface breakout. It has a wide sensitivity range and high resolution, operating with an 10 or 13-bit internal ADC. Built-in motion detection features make tap, double-tap, activity, inactivity, and free-fall detection trivial. There's two interrupt pins, and you can map any of the interrupts independently to either of them.
In stock
+ −
Add to wish list
RJ-45 Ethernet Round Panel Mount Adapter Plug
US$9.17
If you need to add a panel-mount connection for Ethernet, but don't have the time or ability to cut a custom oval or square hole, this RJ-45 Ethernet Round Panel Mount Plug is the easiest and fastest way to panel-ify your existing Ethernet kit. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required. Un-screw the plastic nut, insert the plug and re-attach. Ta-da! Now you have two RJ45's on either side for connecting any cable.
Delivery within 2-3 weeks
+ −
Add to wish list
HDMI Round Panel Mount Plug
US$9.17
If you need to add a panel-mount connection for HDMI, but don't have the time or ability to cut a custom oval or square hole, this HDMI Round Panel Mount Plug is the easiest and fastest way to panel-ify your existing HDMI kit. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required. Un-screw the plastic nut, insert the plug and re-attach. Ta-da! Now you have two HDMI sockets on either side for connecting any cable.
In stock
+ −
Add to wish list
Adafruit ADXL343 + ADT7410 Sensor FeatherWing
US$18.41
Upgrade any Feather board with motion and precision temperature sensing, with this all-in-one sensing FeatherWing. It sports two fantastic sensors from Analog Devices: an ADXL343 triple-axis accelerometer and an ADT7410 precision temperature sensor. Both sensors are connected over the shared I2C bus, so you can use it with any and all Feathers! We also break out the interrupt pins and address-selection jumpers in case you want multiple Feathers or have I2C address conflicts. We've got both Arduino (C/C++) and CircuitPython libraries available so you can use it with any Feather board and get data readings in under 5 minutes.
In stock
+ −
Add to wish list
Adafruit RFM96W LoRa Radio Transceiver Breakout - 433 MHz - RadioFruit
US$30.73
Sending data over long distances is like magic, and now you can be a magician with this range of powerful and easy-to-use radio modules. Sure, sometimes you want to talk to a computer (a good time to use WiFi) or perhaps communicate with a Phone (choose Bluetooth Low Energy!) but what if you want to send data very far? Most WiFi, Bluetooth, Zigbee and other wireless chipsets use 2.4GHz, which is great for high speed transfers. If you aren't so concerned about streaming a video, you can use a lower license-free frequency such as 433 or 900 MHz. You can't send data as fast but you can send data a lot farther.'
In stock
+ −
Add to wish list
Adafruit RFM95W LoRa Radio Transceiver Breakout - 868 or 915 MHz - RadioFruit
US$30.73
Sending data over long distances is like magic, and now you can be a magician with this range of powerful and easy-to-use radio modules. Sure, sometimes you want to talk to a computer (a good time to use WiFi) or perhaps communicate with a Phone (choose Bluetooth Low Energy!) but what if you want to send data very far? Most WiFi, Bluetooth, Zigbee and other wireless chipsets use 2.4GHz, which is great for high speed transfers. If you aren't so concerned about streaming a video, you can use a lower license-free frequency such as 433 or 900 MHz. You can't send data as fast but you can send data a lot farther.'
Delivery within 2-3 weeks
+ −
Add to wish list
Adafruit CharliePlex LED Matrix Bonnet - 8x16 Warm White LEDs
US$21.49
You won't be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet.  This 16x8 LED display can be placed atop any Raspberry Pi computer with a 2x20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C. We carry these Bonnets in a few vivid colors - this is the warm white LED matrix.
In stock
+ −
Add to wish list
Adafruit CharliePlex LED Matrix Bonnet - 8x16 Cool White LEDs
US$21.49
You won't be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet.  This 16x8 LED display can be placed atop any Raspberry Pi computer with a 2x20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C. We carry these Bonnets in a few vivid colors - this is the cool white LED matrix.
Delivery within 2-3 weeks
+ −
Add to wish list
Adafruit CharliePlex LED Matrix Bonnet - 8x16 Green LEDs
US$19.95
You won't be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet.  This 16x8 LED display can be placed atop any Raspberry Pi computer with a 2x20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C. We carry these Bonnets in a few vivid colors - this is the green LED matrix.
In stock
+ −
Add to wish list
Adafruit CharliePlex LED Matrix Bonnet - 8x16 Blue LEDs
US$19.95
You won't be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet.  This 16x8 LED display can be placed atop any Raspberry Pi computer with a 2x20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C. We carry these Bonnets in a few vivid colors - this is the blue LED matrix.
In stock
+ −
Add to wish list
Adafruit CharliePlex LED Matrix Bonnet - 8x16 Yellow LEDs
US$19.95
You won't be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet.  This 16x8 LED display can be placed atop any Raspberry Pi computer with a 2x20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C. We carry these Bonnets in a few vivid colors - this is the yellow LED matrix.
In stock
+ −
Add to wish list
Adafruit USB C Breakout Board - Downstream Connection
US$4.55
Throw out all those Mini and Micro B USB cables you have in a plastic bin - the next generation of USB connectors is here with USB C! You will start to see these connectors pop up on all sorts of devices, as the industry moves from micro B or lightening to the new standard.
In stock
+ −
Add to wish list
1 2 3 4 5 6 7 8 9 10 11
5 - 19