Our Brands

Adafruit

19 - 33
27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
35 - 46
Newest Items First
15 Per Page
373 Breadboard-friendly 2.1mm DC barrel jack
373 Breadboard-friendly 2.1mm DC barrel jack
CA$1.84
This power jack is designed to fit 2.1mm power plugs snugly and securely. Perfect for adding a power connector to your project. We went for the more expensive "thin pin" type which snap into breadboards or perfboards.
In stock
+ −
Add to wish list
610 Panel Mount 2.1mm DC barrel jack
610 Panel Mount 2.1mm DC barrel jack
CA$5.68
This power jack is designed to easily attach to a panel up to 8mm thick (0.315" or 5/16") and fit 2.1mm power plugs snugly and securely. Perfect for adding a power connector to your project enclosure.
In stock
+ −
Add to wish list
724 Terminal Block - 2-pin 3.5mm - pack of 5!
724 Terminal Block - 2-pin 3.5mm - pack of 5!
CA$5.68
These particular 3.5mm terminal blocks are our favorite: big enough for a range of wire gauges, easy to adjust with a screwdriver, and not too chunky. The only down-side is that they do not fit into 2.5mm spaced holes (they're 3.5mm spaced) - but they do fit in most perf/proto-board if you rotate them diagonally.
In stock
+ −
Add to wish list
806 3x8 Male Header - 4 pack
806 3x8 Male Header - 4 pack
CA$5.68
Three rows!? Yes! These chunks of 0.1" header has yet-another-row - handy for when you want to connect cables that come in sets of three, like perhaps sensors, or servos. These plug into any standard 0.1" spacing perf-boards or other PCBs and work nicely with our female-ended wire sets.
In stock
+ −
Add to wish list
562 Panel Mount 10K potentiometer (Breadboard Friendly) - 10K Linear
562-ADA Panel Mount 10K potentiometer (Breadboard Friendly) - 10K Linear
CA$1.84
This potentiometer is a two-in-one, good in a breadboard or with a panel. Its a fairly standard linear taper 10K ohm potentiometer, with a grippy shaft. Its smooth and easy to turn, but not so loose that it will shift on its own.
In stock
+ −
Add to wish list
735 74LVC245 - Breadboard Friendly 8-bit Logic Level Shifter
74LVC245 - Breadboard Friendly 8-bit Logic Level Shifter
CA$2.89
The 74LVC245 is designed so that even when it runs at 1.8V, it still happily accepts 5V signals in one pin and converts it to a lower logic level on the opposite pin. This chip is only for digital signals, it doesn't convert analog signals (you need an op amp for that).
Delivery within 2-3 weeks
+ −
Add to wish list
550 Little Rubber Bumper Feet - Pack of 4
550-ADA Little Rubber Bumper Feet - Pack of 4
CA$1.84
These small sticky bumpers are our favorite accessory for any electronic kit or device. They are sticky, but not impossible to remove. They're small enough to fit onto any board, and have just enough height to give clearance to thru-hole soldered components.
In stock
+ −
Add to wish list
593 MCP23008 - i2c 8 input/output port expander
593 MCP23008 - i2c 8 input/output port expander
CA$3.76
Add another 8 pins to your microcontroller using a MCP23008 port expander. The MCP23008 uses two i2c pins (these can be shared with other i2c devices), and in exchange gives you 8 general purpose pins. You can set each of 8 pins to be input, output, input with a pullup or open drain.
In stock
+ −
Add to wish list
504 Thru-hole 5-way Navigation switch SKQUCAA010
504 Thru-hole 5-way Navigation switch SKQUCAA010
CA$6.24
This navigation switch is an intuitive way to add 5 button's worth of interfacing with a single component. Inside is 5 switches: left, right, up, down and 'select' (pressing down), all with a common ground pin.
In stock
+ −
Add to wish list
753 0.1uF ceramic capacitors - 10 pack
753 0.1uF ceramic capacitors - 10 pack
CA$3.76
A 0.1uF capacitor right next to the VCC pin of your chips will improve stability by filtering out power supply spikes and noise that can cause flaky behavior. We love these little guys, they have 0.1" spacing so fit into any perf or breadboard, compact and good quality.
In stock
+ −
Add to wish list
977 TO-220 Clip-On Heatsink
977 TO-220 Clip-On Heatsink
CA$1.45
977 Adafruit TO-220 Clip-On Heatsink Get the most out of your regulators, transistors and other TO-220 packaged chips by clipping on a heat-sink. Your...
In stock
+ −
Add to wish list
816 3x4 Right Angle Male Header - 4 pack
816 3x4 Right Angle Male Header - 4 pack
CA$5.68
Three rows in a right angle header!? Yes! These chunks of 0.1" header has yet-another-row - handy for when you want to connect cables that come in sets of three, like perhaps sensors, or servos. These plug into any standard 0.1" spacing perf-boards or other PCBs and work nicely with our female-ended wire sets.
Delivery within 2-3 weeks
+ −
Add to wish list
804 PS/2 Wired Connector - Panel Mount MiniDIN-6
804 PS/2 Wired Connector - Panel Mount MiniDIN-6
CA$13.70
This connector is sturdy and easy to panel mount, and has pre-soldered wires connected to the 6 contacts (of which 4 are used).
Delivery within 2-3 weeks
+ −
Add to wish list
383 40-pin ZIF socket
383 40-pin ZIF socket
CA$7.69
This socket is designed for DIP chips of up to 40 pins and up to 0.6" wide. So really, its good for any size chip you'll find. What's nice about it is it can snap into an existing circuit board or socket that is designed for a 40-pin 0.6" chip so you may not have to redesign the board! This socket is gold plated so it will last a long time.
Delivery within 2-3 weeks
+ −
Add to wish list
1134 Breadboard-friendly MIDI Jack (5-pin DIN)
1134 Breadboard-friendly MIDI Jack (5-pin DIN)
CA$3.37
They're what you see on the back of nearly every synthesizer and drum machine. These are nice sturdy jacks, and breadboard-friendly, with all the pins on 0.1" spacing for easy wiring.
In stock
+ −
Add to wish list
19 - 33
27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
35 - 46