Sparkfun

1 2 3 4 5 6 7 8 9 10 11
5 - 19
US$0.79
These standard female headers are made to work with the Particle Photon and Photon ProtoShield boards. Each header adds a great deal of connectivity to your next Photon project. Each order includes one 1x12 female header with pins that are spaced by 0.1". If you don’t have a Particle Photon, that’s fine! These headers will work in any other situation when you need a 12-pin header solution!
In stock
+
Add to wish list

US$1.95
RFID is useful for sensing and identifying tagged people and objects for access control, automation and a whole range of different applications. This basic RFID tag works in the 125kHz RF range and comes with a unique 40-bit ID. It is not reprogrammable. This blank, smooth, mildly flexible RFID tag is ready for your logo (or hand-drawn scribble). Dimensions: 2.13 x 3.35 x 0.03" (54 x 85.5 x 0.8mm).
In stock
+
Add to wish list

US$17.95
This is the SparkFun ESP8266 Thing Dev Board — a development board that has been solely designed around the ESP8266, with an integrated FTDI USB-to-Serial chip. The ESP8266 is a cost-effective and very capable WiFi-enabled microcontroller. Like any microcontroller, it can be programmed to blink LEDs, trigger relays, monitor sensors or automate coffee makers. With an integrated WiFi controller, the ESP8266 is a one-stop shop for almost any internet-connected project. To top it all off, the ESP8266 is incredibly easy to use; firmware can be developed in Arduino and uploaded over a simple serial interface. The ESP8266 Thing Development Board breaks out all of the module’s pins with pre-soldered headers, and the USB-to-serial converter means you don’t need any peripheral components to program the chip. Just plug in a USB cable, download the Arduino board definitions, and start IoT-ing.
Delivery within 1-2 weeks
+
Add to wish list

US$1.50
This is a unique two-cell AA battery holder built specifically for the BBC micro:bit. The 6" (~150mm) cable has been terminated with a JST-PH connector. The connector mates the JST socket on the micro:bit perfectly, allowing you to easily make your project battery powered.
In stock
+
Add to wish list

US$40.95
Are you a Java developer looking to add advanced hardware I/O capabilities to your Android or PC application? Well then the IOIO-OTG is for you! The IOIO-OTG is a development board specially designed to do just that. It features a PIC microcontroller which acts like a bridge that connects an app on your PC or Android device to low-level peripherals like GPIO, PWM, ADC, I2C, SPI, and UART. An app-level library helps you write control code for these low level peripherals in the same way you’d write any other Java app!
Delivery within 1-2 weeks
+
Add to wish list

US$37.95
This is your solution when you absolutely, positively need to get the most out of an antenna for your next RFID project. This ultra high-frequency (UHF) RFID Antenna boasts a frequency range of 860-960 MHz with a gain of 6dBi. This is the same external antenna we use for our Simultaneous RFID Reader (SEN-14066) due to its high-quality features. Each UHF RFID Antenna is terminated with a 30cm long TNC Female RP cable and also includes all the mounting gear you’ll need to attach it to any surface or post you need. If you need to extend the cable attached to the antenna, we offer additional cords (CAB-14132) to help you out!
Delivery within 1-2 weeks
+
Add to wish list

US$5.95
This is a very simple 1m long TNC to RP-SMA cable. We like to use this cable to connect our ultra high-frequency RFID antennas to an equally powerful reader board. This cable is perfect for extending pre-existing cables to give yourself a better range of operations when managing your RFID projects. Each cable is capable of a nominal impedance of 50Ω with a cutoff frequency of 39GHz. If you are looking for a good antenna to pair this cable with, we recommend our UHF RFID Antenna (WRL-14131).
Delivery within 1-2 weeks
+
Add to wish list

US$5.99
The SparkFun micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pins and allowing for connections to the I2C and SPI buses. This breakout board for the micro:bit’s edge connector allows intermediate and advanced users to connect the micro:bit to breadboards and other sensors, motors, LEDs and more! The micro:bit on its own has three digital/analog input/output rings available for you to use initially with alligator clips. With the micro:bit breakout we have broken out all 21 GPIO pins, power and ground to a pre-soldered 0.1" header. With this breakout you will be able to unlock the full potential of your micro:bit!
In stock
+
Add to wish list

US$39.95
The SparkFun Weather Shield is an easy-to-use Arduino shield that grants you access to barometric pressure, relative humidity, luminosity and temperature. There are also connections on this shield to optional sensors such as wind speed, direction, rain gauge and GPS for location and super accurate timing. The Weather Shield utilizes the Si7021 humidity/temperature sensor, the MPL3115A2 barometric pressure sensor and the ALS-PT19 light sensor. The shield relies on the Si7021 and MPL3115A2 Arduino libraries. Each shield comes with two unpopulated RJ11 connector spaces (for optional hookup of rain and wind sensors) and a 6-pin GPS connector (for optional hookup of a GP635T GPS module). Finally, each Weather Shield can operate from 3.3V up to 16V and has built-in voltage regulators and signal translators.
Delivery within 1-2 weeks
+
Add to wish list

US$34.95
The SparkFun Photon Weather Shield is an easy-to-use add-on board that grants you access to barometric pressure, relative humidity, and temperature. There are also connections on this shield to optional sensors such as wind speed, direction, rain gauge and soil readings! These Weather Shields utilize the Si7021 temperature/humidity and MPL3115A2 barometric pressure sensors. Each shield comes with two RJ11 connectors (for optional hookup of rain and wind sensors) and a 3-pin soil temperature and moisture hookup. Finally, each Weather Shield can attach effectively and easily to your Photon in no time at all!
Delivery within 1-2 weeks
+
Add to wish list

US$99.95
The Intel® Edison is an ultra-small computing platform that will change the way you look at embedded electronics. Each Edison packs a huge amount of tech goodies into a tiny package while still providing the same robust strength of your go-to single-board computer. The Edison is powered by the Intel®Atom™ SoC dual-core CPU and includes an integrated WiFi, Bluetooth LE and 70-pin connector to attach a veritable slew of shield-like “Blocks,” which can be stacked on top of one another. It’s no wonder how this little guy is lowering the barrier of entry on the world of electronics! This Edison Base Kit includes all the basic ingredients you need to get started with Intel’s incredibly tiny computer platform. With this pack, you will be able to snap essential parts to your Edison that provide basic functionality and turn it into a modular Linux computer.
In stock
+
Add to wish list

US$19.95
The RedBoard can be programmed over a USB Mini-B cable using the Arduino IDE: Just plug in the board, select “Arduino UNO” from the board menu and you’re ready to upload code. RedBoard has all of the hardware peripherals you know and love: 14 Digital I/O pins with 6 PWM pins, 6 Analog Inputs, UART, SPI and external interrupts. We’ve also broken out the SDA, SCL and IOREF pins that showed up on the UNO R3, so the RedBoard will be compatible with future shields. This version adds an SMD ISP header for use with shields.
Delivery within 1-2 weeks
+
Add to wish list

US$1.95
These paper-thin, adhesive EPCglobal Gen2 tags work with our Simultaneous RFID reader and can be stuck to practically anything you can imagine. The tags can read and be written to — and also have a kill feature. Each tag comes with a TID (Truly Unique ID) that can’t be changed, but there’s plenty of memory for you to write and read from.
Delivery within 1-2 weeks
+
Add to wish list

US$1.95
These paper-thin EPCglobal Gen2 tags work with our Simultaneous RFID reader. The tags can read and be written to — and also have a kill feature. Each tag comes with a TID (Truly Unique ID) that can’t be changed, but there’s plenty of memory for you to write and read from.
Delivery within 1-2 weeks
+
Add to wish list

US$224.95
The SparkFun Simultaneous RFID Reader is an Arduino-compatible board to get you started with the M6E Nano UHF RFID Reader. Radio Frequency Identification (RFID) is becoming popular everywhere for tracking practically everything. Whether you want to get started by adding an RFID reader on your toolbox with tags on all your tools or allowing access to the tree house for your secret society meetings, this board may be for you!
Delivery within 1-2 weeks
+
Add to wish list
1 2 3 4 5 6 7 8 9 10 11
5 - 19