This is a 12 inch five wire cable with 5 pin JST RE connector on both ends.
This is a 4 inch five wire cable with 5 pin JST RE connector on both ends.
This is a 6 inch five wire cable with 5 pin JST RE connector on both ends.
This is a 4 inch six wire cable with 6 pin JST RE connector on both ends.
This is a 6 inch six wire cable with 6 pin JST RE connector on both ends.
This is a four wire cable assembly to one end 4 pin JST connection.
This is a three wire cable assembly to one end 3 pin JST connection.
This is a two wire cable assembly to one end 2 pin JST connection.
This is an automotive two wire cable assembly to a molex 2 pin connection.
This is a six wire cable assembly to one end with a 6 pin JST SH connection.
This is a four wire cable assembly to one end with a 4 pin JST SH connection.
This is a 5 inch simple two wire cable from a 2 pin female 0.1" pitch connector to a 2 pin JST connector.
This is a 5 inch simple two wire cable from a 2 pin JST connector to a open end cable.
This is a 4.7 inch two wire cable from a female 2 pin 0.1" pitch connector to a open end stripped and tinned stranded wire.
This is a package of ten 12 inch single female to female jumper wire set good for prototyping wire connection.
This is a package of a hundred 12 inch single female to female jumper wire set good for prototyping wire connection. Comes in five colors of 20 jumpers each.
This is a package of ten 6 inch single female to male jumper wire set good for prototyping wire connection.
This is a package of a hundred 6 inch single female to male jumper wire set good for prototyping wire connection. Use these to jumper from any male or female header on any board. Multiple jumpers can be installed next to one another on a 0.1" header.
This is a package of a hundred 12 inch single female to male jumper wire set good for prototyping wire connection. Use these to jumper from any male or female header on any board. Multiple jumpers can be installed next to one another on a 0.1" header. Comes in 5 packages of twenty jumpers in each color (colors shown).
This is a package of ten 12 inch single female to male jumper wire set good for prototyping wire connection. Use these to jumper from any male or female header on any board.
This is a package of ten 12 inch single male to male jumper wire set good for prototyping wire connection.
This is a package of a hundred 12 inch single male to male jumper wire set good for prototyping wire connection.
This is a package of a hundred 6 inch single male to male jumper wire set good for prototyping wire connection.
This is a eight inch 8 color wire with a 8 pin JST connector on one end to an open end.
This is a 6 inch six wire cable with a 6 pin molex connector 0.1" spacing on one end to an open wire connection on the other.
This is a 5g syringe of white heatsink compound to use you're connecting a component to a heatsink, it'll really helps to dissipate the potential heat from damaging the components like transistors.
This shifter board kit is a way for you to communicate between your PIC or other IC talking to your computer fast and easy with this board. This is a small custom PCB developed to connect the UART on a microcontroller directly to the computer without the hassle of a MAX232 circuit.
10-pin socket with 2mm pitch that mates with the popular XBee radio from Digi.
This is a two position small pcb mount spring terminal block. Terminals with 0.1" standard spacing. Inserts directly into perf and proto board. Rated up to 150V @ 2A. Terminal can accept 26 to 20AWG wire.
This is a three position small pcb mount spring terminal block. Terminals with 0.1" standard spacing. Inserts directly into perf and proto board. Rated up to 150V @ 2A. Terminal can accept 26 to 20AWG wire.
This is a four position small pcb mount spring terminal block. Terminals with 0.1" standard spacing. Inserts directly into perf and proto board. Rated up to 150V @ 2A. Terminal can accept 26 to 20AWG wire.
This is a six position small pcb mount spring terminal block. Terminals with 0.1" standard spacing. Inserts directly into perf and proto board. Rated up to 150V @ 2A. Terminal can accept 26 to 20AWG wire.
This is a USB type A male connector ideal for making very small USB dongle devices that plug directly into a computer USB port or through a USB A to A extension cable.
This is a micro USB SMD connector to be used primarily on small hand held device where space is limited to have USB access.
This is a female mini-B surface mount connector which has 5 pin connection commonly found in MP3 players, media/disk readers, USB hubs, pretty much anything small and USB.
This breakout board is for 3.5mm audio jack to allow breadboard connection or SIP access to audio feedback. All five pins are broken out.
These spring loaded pogo pins are 33mm (1.3") in length and have round tips. Spring loaded pogo pins are great for programming and applications where you don't always want headers soldered onto your boards. Length: 1.3" (33mm). Travel: 1/4" (6.5mm). Head size 0.05" (1.3mm).Â
These spring loaded pogo pins are 33mm (1.3") in length and have pointed tips. Spring loaded pogo pins are great for programming and applications where you don't always want headers soldered onto your boards. Length: 1.3" (33mm). Travel: 1/4" (6.5mm). Head size 0.05" (1.3mm).Â
These spring loaded pogo pins are 33mm (1.3") in length and have concave tips. Spring loaded pogo pins are great for programming and applications where you don't always want headers soldered onto your boards. Length: 1.3" (33mm). Travel: 1/4" (6.5mm). Head size 0.06" (1.5mm).Â
This is a 10-pin header with 2mm pitch that mates with our XBee socket or anything else you want for connections.
Used with the AVR-PG1, PG2, and JTAG units. Pins have 0.1" spacing between rows and between pins.
6 pin right angle male header use on some of the LilyPad Main Boards. Pins have 0.1" spacing between rows and between pins.
This is a very large row of high quality machine pin headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. Why machine pin? Machine pins are round making better contact with IC sockets and connectors.
These right angle 2 pin JST connector PRT-08612 is a surface mount connector use as a battery connection to Lithium batteries.
Spaced by 2mm and will mate with all of our LiPo batteries.
This is a 1 inch single sided square protoboard. Standard 0.1" spacing with a 4-40 (3mm) hole for mounting. Every three holes are connected with a 20mil trace.. sold in package of 2.
These multimeter tweezer probe is great for testing surface-mount components with standard test lead inputs. Tweezers are 6" long with 10mm open clip distance.
This is a basic 16 character by 2 line LCD black on green background that runs at 5V.