Sparkfun

1 2 3 4 5 6 7 8 9 10 11 12 13 14
8 - 22
US$34.93
Equip your Edison with a graphic display using the Edison OLED Block! Simply snap this board onto your Edison to gain access to a 0.66", 64x48 pixel monochrome OLED. To add some control over your Edison and the OLED, this board also includes a small joystick and a pair of push-buttons which can be used them to create a game, file navigator, or more!
In stock
+
Add to wish list

US$34.93
The Battery Block brings a single cell LiPo Charger and 400mah battery to power an Intel® Edision and expansion cards. The Battery board can be used with an external battery to increase runtime of your Edison which can be pluged in with a micro USB cable to charge.
In stock
+
Add to wish list

US$7.43
The MCP4725 is an I2C controlled Digital-to-Analog converter (DAC). A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller.
In stock
+
Add to wish list

US$3.43
Each 3 position block offers a screw pitch of 10mm with a max current of 15A and a max voltage tolerance of 600V before risking meltdown or implosion.
In stock
+
Add to wish list

US$5.53
This is a 3-terminal microswitch two pack, each equipped with a 17mm lever actuator. These switches have a great ‘clicky’ sound to them with a nice tactile feel and are perfect when used for a slider, 3D printer, or robot project. Each microswitch is rated for 5A at 250VAC.
In stock
+
Add to wish list

US$5.53
Each lead in this pack of ten is 50cm long with a rubber shrouded alligator clip on each end. There are five different colors, you get two each of: red, green, white, black and yellow.
In stock
+
Add to wish list

US$7.81
This is an awesome little microSD USB reader. Just slide your microSD card into the inside of the USB connector, then stick this into a USB port and the card’s contents will pop up on your computer. 
In stock
+
Add to wish list

US$4.92
This is a PTH Addressable RGB LED with a WS2812 control IC built right into the LED.
In stock
+
Add to wish list

US$34.93
Xbee radios are an awesome way to add wireless capability to your Arduino project and now it’s even easier with the XBee Shield. The shield form-factor mates directly with any dev board that has an Arduino standard footprint and equips it with wireless communication capabilities using the popular XBee module. 
In stock
+
Add to wish list

US$83.93
This is the MS5803-14BA Pressure Sensor Breakout, a high resolution pressure sensor with both an I2C and SPI interface. This MEMS pressure sensor measures the absolute pressure of the fluid around it which includes air, water, and anything else that acts like a viscous fluid.
In stock
+
Add to wish list

US$4.92
These are PTH Addressable RGB LEDs with a WS2812 control IC built right into the them.
In stock
+
Add to wish list

US$8.78
This is your simple three conductor sensor cable with electrode pad leads. These cables are 24" long and feature a 3.5mm audio jack connector on one end with snap style receptacles for biomedical sensor pads.
In stock
+
Add to wish list

US$12.54
This is a 10 pack of Biomedical Sensor Pads, disposable electrodes that can be used to measure EEG, ECG and EMG levels. These little pads are perfect for short-term monitoring of Neurofeedback and Biofeedback purposes.
In stock
+
Add to wish list

US$4.19
SD cards are all over the place and they’re great for storing large amounts of data. Why not take advantage by adding an SD socket to your next data heavy project. We use it on a whole bunch of our boards! The SD/MMC ( Secure Digital Disk / Multi Media Cards) cards use a very simple SPI serial bus as well as a 4-bit proprietary bus.
In stock
+
Add to wish list

US$15.06
With SD and MMC memory prices dropping, the time is right for mass storage and datalogging. This breakout board will allow you to breakout the SD/MMC socket to a standard .1" 10-pin header. Perfect for breadboarding and the likes. Board comes fully assembled and tested as shown.
In stock
+
Add to wish list

US$39.05
This is a simple to use, USB to serial base unit for the Digi XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, attach a mini USB cable, and you will have direct access to the serial and programming pins on the XBee unit.
In stock
+
Add to wish list

US$7.53
This is a basic SMA (Sub-Miniature A) male to female connector cable. Each cable is 25cm (9.8") long and has a 50Ω impedance that can handle frequencies up to 17 GHz. 
In stock
+
Add to wish list

US$5.25

If you are looking for a great addressable LED in the more common LED form factor, then this is the perfect choice for you. Features: Power Supply: DC 4.5V - 6V. Internal Frequency: 800K Hz. Single Wire Single Transmission.

In stock
+
Add to wish list

US$7.55 US$6.99
This is a small board that connects to the Raspberry Pi’s 26-pin GPIO connector, and breaks the pins out to breadboard-friendly arrangement and spacing, and even adds a couple of decoupling capacitors on the power supply lines.
In stock
+
Add to wish list

US$39.05
With the XBee Explorer Dongle you can plug the unit directly into your USB port and have it act as a gateway between your computer and the XBee. No cables needed! This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. The on-board voltage regulator is good up to 500mA.
Delivery within 2-3 weeks
+
Add to wish list

US$2.03
This is a 2x23 pin male PTH header. This piece is in the common configuration for Beaglebone Black headers that can be broken apart to form smaller header formations. Each pin has a spacing of 0.1" in between each other.
In stock
+
Add to wish list

US$4.48
This is a 2x23 pin female PTH header, with extra long legs which makes great for stacking. This piece is in the common configuration for Beaglebone Black headers. Each pin has a spacing of 0.1" in between each other.
In stock
+
Add to wish list

US$26.61

If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The USB LiPo Charger is a basic charging circuit that allows you to charge 3.7V LiPo cells at a rate of 500mA or 100mA. It is designed to charge single-cell Li-Ion or Li-Polymer batteries.

In stock
+
Add to wish list

US$15.32
These cases protect your Arduino Uno from things like rogue wires that might short it out while still allowing full access to the board!
In stock
+
Add to wish list

US$24.20
This little breakout that uses the DS1307 to keep track of the current year, month, day as well as the current time. 
In stock
+
Add to wish list

US$9.73

This is a great inexpensive option for wireless communication; it's an ISM band FSK transceiver module implemented with a unique PLL. These modules operate in the 434MHZ band and fully comply with FCC and ETSI regulations.

In stock
+
Add to wish list

US$15.33

This is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of the presence of sound, and an analog representation of its amplitude.

In stock
+
Add to wish list

US$0.96
This is a simple 2x3 male PTH header. This header is in the common configuration for an ISP connector. Each pin has a spacing of 0.1" in between each other.
In stock
+
Add to wish list

US$4.92
This is the Mini Solder-able Breadboard. A bare PCB that is the exact size as our mini modular breadboards with the same connections to pins and power rails. This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in place.
In stock
+
Add to wish list

US$67.50

This complete module is built upon the same technology as the ET-301, but includes on-board voltage regulation, LED status indicator, battery backed RAM, and a built-in patch antenna! 6-pin interface cable included. This EM-506 GPS module is powered by SiRF Star IV, it can provide you with superior sensitivity and performance even in urban canyon and dense foliage environment.

In stock
+
Add to wish list

US$7.14
This is a simple board that breaks out a female USB type A connector's VCC, GND, D- and D+ pins to a 0.1" pitch header. If you want to add a USB to your project, but don't want to put up with soldering tiny connectors, this is the board for you.
In stock
+
Add to wish list

US$2.73
These 6-pin connectors are very similar to the RJ11s we use here in North America except instead of a bottom-mounted hook lock, the BTA uses a side-mounted lock. These BTA connectors are perfect for educators or other users who need to set up a Custom Vernier analog sensor which produces a voltage that changes from high to low or vice versa.
In stock
+
Add to wish list
1 2 3 4 5 6 7 8 9 10 11 12 13 14
8 - 22