Our Brands

Sparkfun

1 - 8
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
10 - 24
Newest Items First
16 Per Page
WIG-13118 SparkFun Servo Trigger
US$26.61
The SparkFun Servo Trigger is a small robotics board that simplifies the control of hobby RC servo motors. When an external switch or logic signal changes state, the Servo Trigger is able to tell an attached servo motor to move from position A to position B. To use the Servo Trigger, you simply connect a hobby servo and a switch, then use the on-board potentiometers to adjust the start/stop positions and the transition time. You can use a hobby servos in your projects without having to do any programming!
In stock
+ −
Add to wish list
PRT-13854 850mAh Lithium Ion Battery
US$13.93
These are very slim, extremely light weight batteries based on Lithium Ion chemistry. Each cell outputs a nominal 3.7V at 850mAh! Comes terminated with a standard 2-pin JST-PH connector - 2mm spacing between pins. These batteries require special charging. Do not attempt to charge these with anything but a specialized LiPo charger. Battery includes built-in protection against over voltage, over current, and minimum voltage.
In stock
+ −
Add to wish list
PRT-10501 JST RCY Connector - Male/Female Set (2-pin)
US$0.98
This is a 2-pin JST RCY connector typically used for low-voltage applications running 10A or less. They are commonly found in RC vehicles. These come in a bag of 1 male plug, 1 female plug, plus pins to connect them both. The pins crimp to your cable and are inserted into the housing.
In stock
+ −
Add to wish list
PRT-13839 Enclosure - Aluminum (112x61x31mm)
US$8.62
These are our small, beefy aluminum enclosures, which have been built tough enough to withstand a truck. This 2mm-thick, die-cast enclosure is rated IP54 against dust and splashing water. Because it’s aluminum, it’s easy to cut and drill so that you can add LCD screens, buttons and cable connections. If you want to “pretty up” your project, hit this with some fine-grit sand paper and buff it or just spray paint it!
In stock
+ −
Add to wish list
KIT-13815 Beefcake Relay Control Kit (Ver. 2.0)
US$14.46
Your 5V system can wield great power with this big, beefy relay board. How does 10A on the NC contacts and 20A on the NO contacts at 220VAC sound? The SparkFun Beefcake Relay Control Kit contains all the parts you need to get your high-power load under control. Only minimal assembly is required! The heart of the board is a sealed, SPDT 20A/10A Relay. The relay is controlled by 5V logic through a transistor, and an LED tells you when the relay is closed.
Delivery within 2-3 weeks
+ −
Add to wish list
BOB-12758 SparkFun Electret Microphone Breakout
US$10.22
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V.
In stock
+ −
Add to wish list
PRT-13856 6Ah Polymer Lithium Ion Battery
US$52.06
These are very compact batteries based on the new Polymer Lithium Ion chemistry. This is the highest energy density currently in production. Each cell outputs a nominal 3.7V at 2000mAh! This solid 3 cell pack (6Ah) comes terminated with a standard 2-pin JST-PH connector - 2mm spacing between pins. Do not attempt to charge these with anything but a charger specifically designed for Lithium Ion batteries.
In stock
+ −
Add to wish list
PRT-13852 40mAh Polymer Lithium Ion Battery
US$6.65
This is an extremely tiny and light weight battery based on the new Polymer Lithium Ion chemistry. This is the highest energy density currently in production. Each cells outputs a nominal 3.7V at 40mAh. This may sound like not so much power, but the cell is really tiny… like, about half an inch square!
In stock
+ −
Add to wish list
SEN-13763 SparkFun Humidity and Temperature Sensor Breakout - Si7021
US$16.73
The Si7021 is a low-cost, easy-to-use, highly accurate, digital humidity and temperature sensor. This sensor is ideal for environmental sensing and data logging and perfect for build a weather stations or humidor control system. All you need are two lines for I2C communication, and you’ll have relative humidity readings and very accurate temperature readings as a bonus!
In stock
+ −
Add to wish list
KIT-13863 SparkFun Picoboard Starter Kit
US$90.93
The SparkFun PicoBoard Starter Kit is your go-to source to begin learning everything about the SparkFun PicoBoard and the Scratch programming environment. This kit includes your very own PicoBoard, multiple pieces of hardware to get you started, and connecting components to get you hooked up. Using the Scratch programming language, you can easily create simple interactive programs based on the input from sensors. The PicoBoard incorporates a light sensor, sound sensor, a button and a slider, as well as four additional inputs that can sense electrical resistance via included cables.
In stock
+ −
Add to wish list
PRT-13813 3.7V 1000mAh Polymer Lithium Ion Battery
US$14.46
These are very slim, extremely light weight batteries based on the new Polymer Lithium Ion chemistry. This is the highest energy density currently in production. Each cell outputs a nominal 3.7V at 1000mAh! Comes terminated with a standard 2-pin JST-PH connector - 2mm spacing between pins. These batteries require special charging.
In stock
+ −
Add to wish list
TOL-11784 SparkFun Third Hand Kit
US$52.17
The SparkFun Third Hand gives you the ability to hold a board between two alligator clips on two flexible arms with multiple points of articulation. The arm’s wide range of articulation gives you access to any angle of the board that you are currently working on, making soldering that much easier. The SparkFun Third Hand also won’t move around while you work thanks to a heavy aluminum base supporting the arms.
In stock
+ −
Add to wish list
DEV-13814 Smooth Thread Bobbin - 12m (Stainless Steel)
US$7.62
This is 12 meters of smooth conductive thread spun from stainless steel fiber and wound on a plastic bobbin. Use it to sew up all of your e-textile projects. This small bobbin is a great way to get into wearable electronics without the upfront cost of buying an entire spool of thread. Close to 40 feet of thread is enough to get a simple design stitched onto your shirt, backpack or hat.
In stock
+ −
Add to wish list
TOL-12942 Bus Pirate - v3.6a
US$45.42
The Bus Pirate v3.6a, created by Ian Lesnet, is a troubleshooting tool that communicates between a PC and any embedded device over 1-wire, 2-wire, 3-wire, UART, I2C, SPI, and HD44780 LCD protocols - all at voltages from 0-5.5VDC. This product eliminates a ton of early prototyping effort when working with new or unknown chips.
Delivery within 2-3 weeks
+ −
Add to wish list
WRL-13002 Telescopic Antenna SMA - 75 MHz to 1 GHz (ANT500)
US$73.29
This ANT500 is a telescopic antenna designed for operation from 75 MHz to 1 GHz with a total length that is configurable from 20 cm to 88 cm long. Each ANT500 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjustable elbow.
Delivery within 2-3 weeks
+ −
Add to wish list
WRL-13001 HackRF One
US$646.07
This is the HackRF One, a Software Defined Radio (SDR) peripheral capable of transmission or reception of radio signals from 1MHz to 6GHz. Designed to enable test and development of modern and next generation radio technologies, HackRF One is an open source hardware platform that can be used as a USB peripheral or programmed for stand-alone operation.
Delivery within 2-3 weeks
+ −
Add to wish list
1 - 8
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
10 - 24