This 2x13 flat ribbon-cable fits the GPIO headers on the Raspberry Pi so you can easily connect to the low-level peripherals and get hacking!Â
This is made to work with the Arduino Uno R3, Leonardo and new Arduino boards going forward. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields. This kit includes 4 headers (2x 8-pin, 1x 10-pin and 1x 6-pin), enough to connect a shield to an Arduino board.
10 pin stackable female header for multiple applications. Pins have 0.1" spacing. Pins are 10.5mm (0.42") in length.
The new version of the Ardubot PCB breaks out all the Arduino pins to a separate row of headers. It also includes spaces for LEDs, a reset switch, and servo headers.
These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the wire leads and within minutes, the pad will begin to warm up.
This is a plastic holder for mounting a mini metal gearmotors. Note: These are sold in singles. No additional hardware is included.
Features: Small 5x3.2mm footprint. Operating temperature: -40-85C. Frequency Tolerance: +/- 20ppm. 18pF load capacitance.
This through-hole speaker is great for projects where you need something that sounds better than a piezo buzzer but don't have room for a full-blown speaker. This 30mm diameter speaker is encased in plastic and will handle about 100mW of power.
This 200 pulse per rotation rotary encoder outputs gray code which you can interpret using a microcontroller and find out which direction the shaft is turning and by how much. This allows you to add feedback to motor control systems. Encoders of this kind are often used in balancing robots and dead reckoning navigation but it could also be used as a very precise input knob.
These are high quality Single Pole - Double Throw (SPDT) sealed relays. Use them to switch high voltage, and/or high current devices. This relay’s coil is rated up to 12V, with a minimum switching voltage of 5V. The contacts are rated up to 5A (@250VAC, 30VDC).
This GPS receiver is a complete GPS smart antenna receiver, that includes an embedded antenna and GPS receiver circuits. This low-cost unit outputs an astounding amount of position information 5 times a second. The receiver is based on the proven technology found in LOCOSYS 66 channel GPS SMD type receivers that use MediaTek chip solution.
This is a 1.75 inch communication cable that connects the EM406 and the EM401.
This is a 1 foot communication cable extension that mates with the EM406 and EM401.
This small servo with a standard 3 pin power and control cable and mounting hardware is similar in size and specifications to the Hitec HS-55 model.
This is a 12 inch servo cable female to female connection with removable plastic shrouds for both ends. This comes in very handy when your servo is further away from the controller than the wire on the servo allows.
This is a 12 inch servo cable female to female connection with removable plastic shrouds for both ends. This comes in very handy when your servo is further away from the controller than the wire on the servo allows.
This is a great way to induce linear motion for pushing, pulling or controlling switches and levers. According to the datasheet this solenoid is rated for 36V but they work like a charm at 12V.
This rotary encoder has a 1024 pulse per rotation rotary encoder outputs gray code which you can interpret using a microcontroller and find out which direction the shaft is turning and by how much. This allows you to add feedback to motor control systems.
This pan/tilt bracket consists of two brackets and all the hardware you need to attach them to make a pan/tilt mechanism using two servo motors.
This is a 12 inch two wire cable with 2 pin JST RE connector on both ends.
This is a 4 inch two wire cable with 2 pin JST RE connector on both ends.
This is a 6 inch two wire cable with 2 pin JST RE connector on both ends.
This is a 12 inch three wire cable with 3 pin JST RE connector on both ends.
This is a 4 inch three wire cable with 3 pin JST RE connector on both ends.
This is a 6 inch three wire cable with 3 pin JST RE connector on both ends.
This is a 12 inch four wire cable with 4 pin JST RE connector on both ends.
This is a 4 inch four wire cable with 4 pin JST RE connector on both ends.
This is a 6 inch four wire cable with 4 pin JST RE connector on both ends.
This is a 12 inch five wire cable with 5 pin JST RE connector on both ends.
This is a 4 inch five wire cable with 5 pin JST RE connector on both ends.
This is a 6 inch five wire cable with 5 pin JST RE connector on both ends.
This is a 4 inch six wire cable with 6 pin JST RE connector on both ends.
This is a 6 inch six wire cable with 6 pin JST RE connector on both ends.
This is a four wire cable assembly to one end 4 pin JST connection.
This is a three wire cable assembly to one end 3 pin JST connection.
This is a two wire cable assembly to one end 2 pin JST connection.
This is an automotive two wire cable assembly to a molex 2 pin connection.
This is a six wire cable assembly to one end with a 6 pin JST SH connection.
This is a four wire cable assembly to one end with a 4 pin JST SH connection.
This is a 5 inch simple two wire cable from a 2 pin female 0.1" pitch connector to a 2 pin JST connector.
This is a 5 inch simple two wire cable from a 2 pin JST connector to a open end cable.
This is a 4.7 inch two wire cable from a female 2 pin 0.1" pitch connector to a open end stripped and tinned stranded wire.
This is a package of ten 12 inch single female to female jumper wire set good for prototyping wire connection.
This is a package of a hundred 12 inch single female to female jumper wire set good for prototyping wire connection. Comes in five colors of 20 jumpers each.
This is a package of ten 6 inch single female to male jumper wire set good for prototyping wire connection.
This is a package of a hundred 6 inch single female to male jumper wire set good for prototyping wire connection. Use these to jumper from any male or female header on any board. Multiple jumpers can be installed next to one another on a 0.1" header.
This is a package of a hundred 12 inch single female to male jumper wire set good for prototyping wire connection. Use these to jumper from any male or female header on any board. Multiple jumpers can be installed next to one another on a 0.1" header. Comes in 5 packages of twenty jumpers in each color (colors shown).
This is a package of ten 12 inch single female to male jumper wire set good for prototyping wire connection. Use these to jumper from any male or female header on any board.
This is a package of ten 12 inch single male to male jumper wire set good for prototyping wire connection.
This is a package of a hundred 12 inch single male to male jumper wire set good for prototyping wire connection.
This is a package of a hundred 6 inch single male to male jumper wire set good for prototyping wire connection.
This is a eight inch 8 color wire with a 8 pin JST connector on one end to an open end.
This is a 6 inch six wire cable with a 6 pin molex connector 0.1" spacing on one end to an open wire connection on the other.
This is a 5g syringe of white heatsink compound to use you're connecting a component to a heatsink, it'll really helps to dissipate the potential heat from damaging the components like transistors.
This shifter board kit is a way for you to communicate between your PIC or other IC talking to your computer fast and easy with this board. This is a small custom PCB developed to connect the UART on a microcontroller directly to the computer without the hassle of a MAX232 circuit.
10-pin socket with 2mm pitch that mates with the popular XBee radio from Digi.
This is a two position small pcb mount spring terminal block. Terminals with 0.1" standard spacing. Inserts directly into perf and proto board. Rated up to 150V @ 2A. Terminal can accept 26 to 20AWG wire.
This is a three position small pcb mount spring terminal block. Terminals with 0.1" standard spacing. Inserts directly into perf and proto board. Rated up to 150V @ 2A. Terminal can accept 26 to 20AWG wire.
This is a four position small pcb mount spring terminal block. Terminals with 0.1" standard spacing. Inserts directly into perf and proto board. Rated up to 150V @ 2A. Terminal can accept 26 to 20AWG wire.
This is a six position small pcb mount spring terminal block. Terminals with 0.1" standard spacing. Inserts directly into perf and proto board. Rated up to 150V @ 2A. Terminal can accept 26 to 20AWG wire.
This is a USB type A male connector ideal for making very small USB dongle devices that plug directly into a computer USB port or through a USB A to A extension cable.
This is a micro USB SMD connector to be used primarily on small hand held device where space is limited to have USB access.
This is a female mini-B surface mount connector which has 5 pin connection commonly found in MP3 players, media/disk readers, USB hubs, pretty much anything small and USB.
This breakout board is for 3.5mm audio jack to allow breadboard connection or SIP access to audio feedback. All five pins are broken out.
These spring loaded pogo pins are 33mm (1.3") in length and have round tips. Spring loaded pogo pins are great for programming and applications where you don't always want headers soldered onto your boards. Length: 1.3" (33mm). Travel: 1/4" (6.5mm). Head size 0.05" (1.3mm).Â
These spring loaded pogo pins are 33mm (1.3") in length and have pointed tips. Spring loaded pogo pins are great for programming and applications where you don't always want headers soldered onto your boards. Length: 1.3" (33mm). Travel: 1/4" (6.5mm). Head size 0.05" (1.3mm).Â
These spring loaded pogo pins are 33mm (1.3") in length and have concave tips. Spring loaded pogo pins are great for programming and applications where you don't always want headers soldered onto your boards. Length: 1.3" (33mm). Travel: 1/4" (6.5mm). Head size 0.06" (1.5mm).Â
This is a 10-pin header with 2mm pitch that mates with our XBee socket or anything else you want for connections.
Used with the AVR-PG1, PG2, and JTAG units. Pins have 0.1" spacing between rows and between pins.
6 pin right angle male header use on some of the LilyPad Main Boards. Pins have 0.1" spacing between rows and between pins.
This is a very large row of high quality machine pin headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. Why machine pin? Machine pins are round making better contact with IC sockets and connectors.
These right angle 2 pin JST connector PRT-08612 is a surface mount connector use as a battery connection to Lithium batteries.
Spaced by 2mm and will mate with all of our LiPo batteries.
This is a 1 inch single sided square protoboard. Standard 0.1" spacing with a 4-40 (3mm) hole for mounting. Every three holes are connected with a 20mil trace.. sold in package of 2.
These multimeter tweezer probe is great for testing surface-mount components with standard test lead inputs. Tweezers are 6" long with 10mm open clip distance.
This is a basic 16 character by 2 line LCD black on green background that runs at 5V.