This is the comprehensive guide to ZigBee wireless networks. This kit includes many of the parts and pieces you will need to work through the examples in the book. If you're serious about learning everything you need to know about XBee networks, this kit and the book will get you up to speed in no time (or as long as it takes you to get through the book).
These are bare addressable 5 meter long RGB LED strips that come packed with 60 WS2812s per meter. As these are bare LED strips that have no protective coating, your project won't be water proof but there is access to each WS2812 LED and each strip length can be easily modified. You will be able to control each LED RGB individually giving you the ability to create cool lighting effects for your car or perhaps under cabinet lighting in your kitchen!
This GPS receiver is a complete GPS smart antenna receiver, that includes an embedded antenna and GPS receiver circuits. This low-cost unit outputs an astounding amount of position information 5 times a second. The receiver is based on the proven technology found in LOCOSYS 66 channel GPS SMD type receivers that use MediaTek chip solution.
This rotary encoder has a 1024 pulse per rotation rotary encoder outputs gray code which you can interpret using a microcontroller and find out which direction the shaft is turning and by how much. This allows you to add feedback to motor control systems.
This 200 pulse per rotation rotary encoder outputs gray code which you can interpret using a microcontroller and find out which direction the shaft is turning and by how much. This allows you to add feedback to motor control systems. Encoders of this kind are often used in balancing robots and dead reckoning navigation but it could also be used as a very precise input knob.
This Liquid Level Sensor from Milone Technologies is a great way to measure the level of a liquid. It has a resistive output that varies with the level of the fluid. It does away with clunky mechanical floats, and easily interfaces with electronic control systems.
This complete module is built upon the same technology as the ET-301, but includes on-board voltage regulation, LED status indicator, battery backed RAM, and a built-in patch antenna! 6-pin interface cable included. This EM-506 GPS module is powered by SiRF Star IV, it can provide you with superior sensitivity and performance even in urban canyon and dense foliage environment.
This is a package of a hundred 12 inch single female to female jumper wire set good for prototyping wire connection. Comes in five colors of 20 jumpers each.
This is a package of a hundred 12 inch single female to male jumper wire set good for prototyping wire connection. Use these to jumper from any male or female header on any board. Multiple jumpers can be installed next to one another on a 0.1" header. Comes in 5 packages of twenty jumpers in each color (colors shown).
This is a package of a hundred 12 inch single male to male jumper wire set good for prototyping wire connection.
This is a OpenScale from “SparkFun” is a simple-to-use, open source solution for measuring weight and temperature. It has the ability to read multiple types of load cells and offers a simple-to-use serial menu to configure calibration value, sample rate, time stamp and units of precision.
This large matrix has 64 Red, 64 Green and 64 Blue individual LEDs built into one common cathode housing. Unit comes with a black finish and a opaque LED lenses.
This is a package of a hundred 6 inch single female to male jumper wire set good for prototyping wire connection. Use these to jumper from any male or female header on any board. Multiple jumpers can be installed next to one another on a 0.1" header.
This is a package of a hundred 6 inch single male to male jumper wire set good for prototyping wire connection.
Kit Includes: 5x Mini Photocell, 5x 10k Trimpot, 2x Gear Hobby Motor, 2x Generic Servo (Sub-Micro Size), 2x Bag of 25 10kOhm Resistor, 2x Bag of 25 330Ohm Resistor, 5x 30 Pack of Jumper Wires, 10x 1N4148 Diode, 1x Assorted LED (20 Pack) - (5 Red, 5 Blue, 5 Yellow, 5 Green). 1x Simon Buttons (4 Pack) - (1 Red, 1 Blue, 1 Yellow, 1 Green).
This provides a very easy way to start using MOSFETS for your next high current project. This shield allows you to use a computer power supply (or any other power source) to use your Arduino to switch high current. With RFP30N06LE MOSFETS, you can easily control a lot of current directly from your Arduino.
These are bare addressable 1 meter long RGB LED strips that come packed with 60 WS2812s per meter. As these are bare LED strips that have no protective coating, your project won't be water proof but there is access to each WS2812 LED and each strip length can be easily modified.
Features: 25 RGB LEDs. Standard size - T1 3/4 5mm. 2800/6500/1200 mcd brightness. 2.0V/3.2V/3.2V forward drop. Max current 20mA.
This is a great way to induce linear motion for pushing, pulling or controlling switches and levers. According to the datasheet this solenoid is rated for 36V but they work like a charm at 12V.
Dimensions: Overall Display: 127 x 101.6 mm (5.00" x 4.00"). Digit Height: 153mm (6.02").
This is a 5V Arduino running the 16MHz bootloader meant for advanced users that understand the limitations of system voltage. Arduino Pro does not come with connectors populated so that you can solder in any connector or wire with any orientation you need.
If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The USB LiPo Charger is a basic charging circuit that allows you to charge 3.7V LiPo cells at a rate of 500mA or 100mA. It is designed to charge single-cell Li-Ion or Li-Polymer batteries.
This is a basic 16 character by 2 line LCD black on green background that runs at 5V.
After you've assembled it, simply plug the RaspiRobot Board into the GPIO port on the Raspberry Pi and it provides dual bi-directional motor controllers, two open collector outputs, two switch inputs, a pair of status LEDs and even a voltage regulator capable of powering the Pi using a battery source from 7-12VDC.
This is a package Joystick Shield Kit that requires assembly all inside a clear clamshell. Five momentary push buttons (4+ joystick select button) and a two-axis thumb joystick gives your Arduino functionality on the level of old Nintendo controllers.
This is a FTDI cable converter which allows for a simple way to connect serial (TTL) interface devices to USB. The I/O pins of this FTDI cable are configured to operate at 5V. The FTDI cable is designed around an FT232RQ, which is housed in a USB A connector.
This is a FTDI cable converter which allows for a simple way to connect serial (TTL) interface devices to USB. but also configured to operate at 5V with 3.3V I/O. The FTDI cable is designed around an FT232RQ, which is housed in a USB A connector.