Sparkfun

US$20.93
This is a very simple board that takes a 6-12V input voltage and outputs a selectable 5V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard.
Delivery within 2-3 weeks
+
Add to wish list

US$20.93
The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). It requires a 6V to 30V supply to power the motor and can power any voltage of stepper motor.
In stock
+
Add to wish list

US$14.64
This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the ‘alarm’ pin will go low. This unit works great from 5 to 12V. You can also install a jumper wire past the 5V regulator on board to make this unit work at 3.3V. Sensor uses 1.6mA@3.3V.
In stock
+
Add to wish list

US$7.43
This is a breakout PTH soldering kit for for the RFP30N06LE N-Channel MOSFET. This kit is extremely simple to assemble with only 10 pins to solder.
In stock
+
Add to wish list

US$28.81
This is a breakout for the VL6180 distance sensor. Unlike most distance sensors that rely reflected light intensity or reflected angles to determine range, the VL6180 uses a precise clock to measure the time it takes light to bounce back from a surface.
In stock
+
Add to wish list

US$8.47
This is the SparkFun RJ45 MagJack Breakout, a simple board that will provide you with a way to put an ethernet port into your breadboard. The SparkFun RJ45 MagJack Breakout is the same one found in our very own mbed Starter Kit and breaks out each pin from the ethernet jack.
Delivery within 2-3 weeks
+
Add to wish list

US$26.13
This is a stepper motor driver board for bi-polar stepper motors up to a max 2A/phase. It is based on the Allegro A4988 stepper driver chip. It’s the next version of the popular Easy Driver board.
In stock
+
Add to wish list

US$2.45
This is a simple three wire cable. Each cable is 6" long and is great for jumping from board to board or just about anything else. There is a 3-pin JST connector with 0.1" spacing on both ends.
In stock
+
Add to wish list

US$9.73
This Micro Gripper is capable of opening 2.75" wide max, has an overall body length of 1.7" long with a 1.3" wide servo housing body, and offers three 6-32 mounting thru-holes along the edges of the servo housing.
In stock
+
Add to wish list

US$9.73
This Micro Gripper is capable of opening 2.75" wide max, has an overall body dimension of 2.6" long by 1.3" wide, and offers the 0.77" hub pattern for easy mounting on Actobotics components.
In stock
+
Add to wish list

US$72.73
This is an all-in-one kit that offer everything you need to get your next RFID project off the ground. This kit includes our USB RFID Reader, ID-12LA RFID module, and two 125kHz RFID cards. We’ve done away with the annoying clamshell and now offer this in the same type of box as the rest of our kits.
In stock
+
Add to wish list

US$43.49
These pliers are capable of crimping very small 0.25 - 1.5mm crimp pins and 28-20 AWG wires together. All you need to do is press the handles together with enough force and the pliers will release, once this happens you know your crimping is done! These work well with JST PH, SH, SHL, and ZH series pins.
Delivery within 2-3 weeks
+
Add to wish list

US$24.20
This is the SparkFun USB to Serial Breakout for the FT232RL, a small board with a built in USB to serial UART interface. This little breakout is built around the FT232RL IC from FTDI, with an internal oscillator, EEPROM, and a 28-pin SSOP package this is a serious little chip.
In stock
+
Add to wish list

US$51.49
This is an involved PTH soldering kit that allows you to quickly and accurately dial in a specific resistance value between 0 and 999,990 Ω, in 10 Ω increments. The concept is simple, a decade box is a tool that contains resistors of many values that can be accessed via mechanical switches.
Delivery within 2-3 weeks
+
Add to wish list

US$69.93
The SparkFun Mini Inventor’s Kit (SMIK) is a great way to get started with programming and hardware interaction with the Arduino programming language. This mini SIK includes everything you need to complete 8 circuits that will teach you how to blink an LED, read sensors, drive servos, and more. You don’t need any previous programming or electronics experience to use this kit.
Delivery within 2-3 weeks
+
Add to wish list