This 2x13 flat ribbon-cable fits the GPIO headers on the Raspberry Pi so you can easily connect to the low-level peripherals and get hacking!Â
This is made to work with the Arduino Uno R3, Leonardo and new Arduino boards going forward. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields. This kit includes 4 headers (2x 8-pin, 1x 10-pin and 1x 6-pin), enough to connect a shield to an Arduino board.
10 pin stackable female header for multiple applications. Pins have 0.1" spacing. Pins are 10.5mm (0.42") in length.
The new version of the Ardubot PCB breaks out all the Arduino pins to a separate row of headers. It also includes spaces for LEDs, a reset switch, and servo headers.
These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the wire leads and within minutes, the pad will begin to warm up.
This is a plastic holder for mounting a mini metal gearmotors. Note: These are sold in singles. No additional hardware is included.
Features: Small 5x3.2mm footprint. Operating temperature: -40-85C. Frequency Tolerance: +/- 20ppm. 18pF load capacitance.
This through-hole speaker is great for projects where you need something that sounds better than a piezo buzzer but don't have room for a full-blown speaker. This 30mm diameter speaker is encased in plastic and will handle about 100mW of power.
This 200 pulse per rotation rotary encoder outputs gray code which you can interpret using a microcontroller and find out which direction the shaft is turning and by how much. This allows you to add feedback to motor control systems. Encoders of this kind are often used in balancing robots and dead reckoning navigation but it could also be used as a very precise input knob.
These are high quality Single Pole - Double Throw (SPDT) sealed relays. Use them to switch high voltage, and/or high current devices. This relay’s coil is rated up to 12V, with a minimum switching voltage of 5V. The contacts are rated up to 5A (@250VAC, 30VDC).
This GPS receiver is a complete GPS smart antenna receiver, that includes an embedded antenna and GPS receiver circuits. This low-cost unit outputs an astounding amount of position information 5 times a second. The receiver is based on the proven technology found in LOCOSYS 66 channel GPS SMD type receivers that use MediaTek chip solution.
This is a 1.75 inch communication cable that connects the EM406 and the EM401.
This is a 1 foot communication cable extension that mates with the EM406 and EM401.
This small servo with a standard 3 pin power and control cable and mounting hardware is similar in size and specifications to the Hitec HS-55 model.
This is a 12 inch servo cable female to female connection with removable plastic shrouds for both ends. This comes in very handy when your servo is further away from the controller than the wire on the servo allows.
This is a 12 inch servo cable female to female connection with removable plastic shrouds for both ends. This comes in very handy when your servo is further away from the controller than the wire on the servo allows.
This is a great way to induce linear motion for pushing, pulling or controlling switches and levers. According to the datasheet this solenoid is rated for 36V but they work like a charm at 12V.
This rotary encoder has a 1024 pulse per rotation rotary encoder outputs gray code which you can interpret using a microcontroller and find out which direction the shaft is turning and by how much. This allows you to add feedback to motor control systems.
This pan/tilt bracket consists of two brackets and all the hardware you need to attach them to make a pan/tilt mechanism using two servo motors.
This is a 12 inch two wire cable with 2 pin JST RE connector on both ends.
This is a 4 inch two wire cable with 2 pin JST RE connector on both ends.
This is a 6 inch two wire cable with 2 pin JST RE connector on both ends.
This is a 12 inch three wire cable with 3 pin JST RE connector on both ends.
This is a 4 inch three wire cable with 3 pin JST RE connector on both ends.
This is a 6 inch three wire cable with 3 pin JST RE connector on both ends.
This is a 12 inch four wire cable with 4 pin JST RE connector on both ends.
This is a 4 inch four wire cable with 4 pin JST RE connector on both ends.
This is a 6 inch four wire cable with 4 pin JST RE connector on both ends.
This is a 12 inch five wire cable with 5 pin JST RE connector on both ends.
This is a 4 inch five wire cable with 5 pin JST RE connector on both ends.