Sensors RFID

Low Frequency (LF)

 The LF band covers frequencies from 30 KHz to 300 KHz. Typically LF RFID systems operate at 125 KHz. This frequency band provides a short read range of 10 cm, and has slower read speed than the higher frequencies, but is not very sensitive to radio wave interference.

High Frequency (HF)

The HF band ranges from 3 to 30 MHz. Most HF RFID systems operate at 13.56 MHz with read ranges between 10 cm and 1 m. HF systems experience moderate sensitivity to interference. 

Ultra High Frequency (UHF)

The UHF frequency band covers the range from 300 MHz to 3 GHz. Typically UHF RFID systems operate at 860 to 960 MHz. This frequency band provides a range of 12m, they are also faster than HF and LF RFIDs. Special tags are designed to alleviate signal noise loss.

1 2 3
US$3.50

125KHZ RFID Read only Silicone Bracelet, Black and is used for ID access.

In stock
+
Add to wish list

US$3.14

125KHZ RFID Rewriteable Silicone Bracelet, Orange and is used for ID access.

In stock
+
Add to wish list

US$3.50
This is an RFID (Radio-Frequency Identification) bracelet that is pre-programmed and can be used for a multitude of security/access applications. It responds to 13.56MHz frequency (I-CODE2) and works at a distance of 2-10cm.
In stock
+
Add to wish list

US$3.14
This is an RFID (Radio-Frequency Identification) bracelet that is pre-programmed and can be used for a multitude of security/access applications. It responds to 13.56MHz frequency (I-CODE2) and works at a distance of 2-10cm. The tag itself is small and is water-resistant made of ABS plastic. The tag does not require any batteries or wires and has a 1024K bit memory capacity.
In stock
+
Add to wish list

US$18.15
The EM-18 Radio frequency Identification (RFID)</strong><span> </span>is a wireless identification technology that uses radio waves to identify the presence of RFID tags.
In stock
+
Add to wish list

US$2.59

WL-NTAG213 RFID Ntag213 NFC Tags Sticker 13.56MHz is used for data transfer, sharing media and more between two devices that are in proximity.

In stock
+
Add to wish list

US$29.75

‎ WL-369  RFID Card Reader 125KHz USB mini  EM4100

In stock
+
Add to wish list

US$18.15
This product is a bundle that comes with 3  rewritable tags and one portable RFID reader. It's able to take existing 125Khz RFID tags/cards and back them up into a blank tag.
In stock
+
Add to wish list

US$72.75
This device is a RFID reader/writer/copier/duplicator with USB cable supporting 125Khz and 13.56Mhz  (IC MODE).
In stock
+
Add to wish list

US$31.80
13.56MHz Single-Door RFID Access Controller Box with EM-ID Card A single-door access control system kit is very suitable for a single room or shop as...
In stock
+
Add to wish list

US$21.61
125KHz Single-Door RFID Access Controller Box with EM-ID Card A single-door access control system kit is very suitable for a single room or shop as well...
In stock
+
Add to wish list

US$35.00
Maduino Zero NFC is an Arduino compatible small development board with NFC (Near-Field Communication). This board will be the bridge that helps you wirelessly interact with your environment, drive motors, unlock strikes, control relays, read from a temperature sensor and all thanks to built-in NFC connectivity, right out of the box. Same other Maduino Zero boards, this board is based on ATSAMD21G18(which actually makes it available to work with MicroPython, if you re-program the bootloader).
In stock
+
Add to wish list

US$30.99
This is an NFC development kit based on ST25R3911B, with STM32F103R controller, OLED display, user buttons, and common used interfaces. It is your ideal choice for learning and developing NFC applications. Multiple NFC protocols are supported by the kit, with up to 1.4w output power, and low-power capacitive wakeup function.
In stock
+
Add to wish list

US$24.95
This is a PN532 NXP chip-based highly integrated RFID transceiver module for contactless communication at 13.56 MHz based on the 80C51 microcontroller core.
In stock
+
Add to wish list

US$29.95
This CLRC663, the high-performance multi-protocol NFC frontends is an NXP based IC RFID Transceiver works for Near Field Communication.
In stock
+
Add to wish list
1 2 3