Our Brands

Sensor Shields

Newest Items First
15 Per Page
COM-15453 EasyVR Plus Shield - Voice Recognition Shield
US$72.75
The EasyVR Plus Shield 3.0 is a voice recognition shield for Arduino boards integrating an EasyVR module. It includes all of the features of the EasyVR module in a shield form factor that simplifies connection to the Arduino main board and PC.
Delivery within 2-3 weeks
+ −
Add to wish list
AM-143 NE555 Adjustable Pulse Frequency Duty Cycle Module Square Wave Signal Generator
US$3.75
This is an adjustable square wave signal generator with pulse frequency duty cycle using the good old NE555 Chip to output a pulse at a frequency determined by an adjustable resistance at the end of the module. LOad in between 5 and 12V and it’ll output a square wave.
In stock
+ −
Add to wish list
SEN0481, Magnetic Contact Switch Sensor for Arduino
US$7.00
The SEN0481 is a magnetic control switch composed of a pair of reeds that compact and send a signal when exposed to a suitable external magnetic field.
 
In stock
+ −
Add to wish list
ARD-MFB Arduino Uno Multi-Purpose-Board Shield
US$5.48
If you are new to the Arduino platform, this Shield has it all! It can help you understand the basic concepts of different sensors, LEDs, Buzzers, Serial and I2C communications, switches and more! All you have to do is plug it on top of the Arduino UNO and upload the corresponding code to have fun!
In stock
+ −
Add to wish list
SENS-9IN1 Arduino Uno 9 In 1 Sensor Shield
US$12.99
If you are new to the Arduino platform, this Arduino Shield has it all! It can help you understand the basic concepts of sensors, LEDs, Buzzers, Serial and I2C communications.
In stock
+ −
Add to wish list
ARD-614 Arduino Mega2560 Sensor Shield
US$6.15
This Sensor Shield for Arduino Mega compatible microcontrollers makes interfacing with sensors and servos a breeze. All digital pins have been shifted inwards from where you would usually find them and next to the Digital Pins (S) are Gnd (G) and Vcc (V) bus. You can remove the jumper near the terminal block (SEL) and supply any fixed voltage from the terminal block you want for the entire Vcc bus or keep the jumper in place and offer 5v from Arduino 5V pin. Offers a LCD parallel and LCD Serial connector port. You also have access on the analog pins located below the pushbutton. The push button allows user to reset the microcontroller and see with two led indicators for status and power. There are other dedicated headers below the Analog pin for Bluetooth connection, APC220 connection, SPI connection and I2C connection. This board in summary brings all the Arduino pins closer and offers option to provide power for your sensor/servo needs. Great for robotics or any generic project that requires sensors, motors or any other peripheral to attach.
In stock
+ −
Add to wish list
AM-140 Square Wave Generator with adjustable ratio and frequency
US$7.69
This small module uses an LM358 to output a square wave at a frequency determined small jumpers and an adjustable resistance at the end of the module, with the duty cycle adjusted by the potentiometer at the center of the module. Put in between 5 and 12V and it’ll start right away.
In stock
+ −
Add to wish list
AM-135 NE555 Frequency Adjustable Pulse Generator Module
US$6.15
This small module uses the good old NE555 to output a pulse at a frequency determined by an adjustable resistance at the end of the module. Put in between 5 and 12V and it’ll output a square wave. A small LED lights up to show the device is powered.
In stock
+ −
Add to wish list
EF02038 Touch Shield
US$9.73
The MPR121 IC is a great way to build simple capacitive touch interfaces, and now it's even easier to incorporate into your Arduino projects with the touch shield. The touch shield has 12 capacitive touch pads. With this shield you can have a total of 12 touch sensitive buttons.
In stock
+ −
Add to wish list
ARD-SS Arduino Sensor Shield
US$9.10
This Sensor Shield for Arduino Uno compatible microcontrollers makes interfacing with sensors and servos a breeze. All digital pins have been shifted inwards from where you would usually find them and next to the Digital Pins (S) are Gnd (G) and Vcc (V) bus. You can remove the jumper near the terminal block (SEL) and supply any fixed voltage from the terminal block you want for the entire Vcc bus or keep the jumper in place and offer 5v from Arduino 5V pin.
In stock
+ −
Add to wish list
2024-ADA Adafruit 12 x Capacitive Touch Shield for Arduino - MPR121
US$19.25
This touch-able add on shield for Arduinos will inspire your next interactive project with 12 capacitive touch sensors.
In stock
+ −
Add to wish list
DFR0151 Real Time Clock Module (DS1307) V1.1
DFR0151 Real Time Clock Module (DS1307) V1.1
US$9.73
The module comes fully assembled and pre-programmed with the current time (ok, so it's our current time - MST).
In stock
+ −
Add to wish list
RTL-10774 Touch Sensor Shield
RTL-10774 Touch Sensor Shield
US$22.33
The MPR121 IC is a great way to build simple capacitive touch interfaces, and now it's even easier to incorporate into your Arduino projects with the touch shield. The touch shield has 9 capacitive touch pads, with headers for the remaining 3 electrode connections.
In stock
+ −
Add to wish list
DEV-10508 Touch Shield
DEV-10508 Touch Shield
US$20.93

A great way to build simple capacitive touch interfaces, and now it's even easier to incorporate into your Arduino projects with the touch shield. The touch shield has 9 capacitive touch pads, with headers for the remaining 3 electrode connections. With this shield you can have a total of 12 touch sensitive buttons.

In stock
+ −
Add to wish list