Pololu

1 2 3 4 5 6 7 8 9
3 - 17
US$6.36
These black plastic wheels have silicone tires and measure 40 mm (1.57″) in diameter. They mount onto micro servo splines with 20 teeth and a 4.8 mm diameter, such as the splines on FEETECH’s FS90R micro continuous rotation servos and FT90R digital micro continuous rotation servos. This product is a pair of wheels.
In stock
+
Add to wish list

US$7.94
These black plastic wheels have silicone tires and measure 60 mm (2.36″) in diameter. They mount onto micro servo splines with 20 teeth and a 4.8 mm diameter, such as the splines on FEETECH’s FS90R micro continuous rotation servos and FT90R digital micro continuous rotation servos. This product is a pair of wheels.
In stock
+
Add to wish list

US$11.13
Add quadrature encoders to your micro metal gearmotors (extended back shaft version required) with this kit that uses a magnetic disc and hall effect sensors to provide 12 counts per revolution of the motor shaft. The sensors operate from 2.7 V to 18 V and provide digital outputs that can be connected directly to a microcontroller or other digital circuit.
In stock
+
Add to wish list

US$11.13
Add quadrature encoders to your micro metal gearmotors (extended back shaft version required) with this kit that uses a magnetic disc and hall effect sensors to provide 12 counts per revolution of the motor shaft. The sensors operate from 2.7 V to 18 V and provide digital outputs that can be connected directly to a microcontroller or other digital circuit.
In stock
+
Add to wish list

US$3.49
This 75 cm (30″) cable has six 28 AWG wires and a 6-pin female JST SH-type connector that works with our Micro Metal Gearmotor Encoders with top-entry connectors and with side-entry connectors. The other ends of the wires are unterminated; they can be cut to length to match your application.
In stock
+
Add to wish list

US$2.19
This 30 cm (12″) cable has six 28 AWG wires and a 6-pin female JST SH-type connector that works with our Micro Metal Gearmotor Encoders with top-entry connectors and with side-entry connectors. The other ends of the wires are unterminated; they can be cut to length to match your application.
In stock
+
Add to wish list

US$21.02
The Pololu TB67S128FTG Stepper Motor Driver Carrier breakout board makes it easy to use Toshiba’s TB67S128FTG microstepping bipolar stepper motor driver, which features adjustable current limiting and microstepping down to 1/128-step. In addition, it has the ability to dynamically select an optimal decay mode by monitoring the actual motor current, and it can automatically reduce the driving current below the full amount when the motor is lightly loaded to minimize power consumption and heat generation.
In stock
+
Add to wish list

US$22.52
This compact breakout board for Maxim’s MAX14870 motor driver offers a wide operating voltage range of 4.5 V to 36 V and can deliver a continuous 1.7 A (2.5 A peak) to a single brushed DC motor. It features a simple two-pin speed/direction interface and built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature.
In stock
+
Add to wish list

US$6.93
The compact (0.4″ × 0.5″) D24V5F3 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 3.3 V while allowing for a maximum output current of 500 mA. This regulator offers typical efficiencies between 80% and 90% and has a very low dropout, so it can be used with input voltages as low as a few hundred millivolts above 3.3 V. The pins have a 0.1″ spacing, making this board compatible with standard solderless breadboards and perfboards.
In stock
+
Add to wish list

US$17.92
This version of our TB67S249FTG Stepper Motor Driver Compact Carrier ships with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. The TB67S249FTG has a wide operating voltage range of 10 V to 47 V, and our carrier board can deliver approximately 1.6 A per phase continuously without a heat sink or forced air flow (up to 4.5 A peak).
In stock
+
Add to wish list

US$13.93
These premium wires are stranded 26 AWG wires with female terminals on both ends. Together with our 0.1″ crimp connector housings, these wires can be used to make custom cables with 0.1″ (2.54mm) connectors. The assortment of 6″ (15 cm) wires includes five each of ten different colors.
In stock
+
Add to wish list

US$13.96
This version of our STSPIN820 Stepper Motor Driver Carrier ships with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard.
In stock
+
Add to wish list

US$15.20
This version of our TB67S279FTG Stepper Motor Driver Compact Carrier ships with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. The TB67S279FTG has a wide operating voltage range of 10 V to 47 V, and our carrier board can deliver approximately 1.1 A per phase continuously without a heat sink or forced air flow (up to 2 A peak).
In stock
+
Add to wish list

US$8.63
This coated steel bracket lets you securely mount typical NEMA 23-size stepper motors to your project. The bracket features two slots for various mounting solutions and includes four M4×16mm screws, washers, and nuts for securing the motor to the bracket.
In stock
+
Add to wish list

US$7.56
This array of IR LED/phototransistor pairs is great for precisely identifying changes in reflectance (like line detection). It operates from 2.9 V to 5.5 V and offers dimmable brightness control independent of the supply voltage. In general, the closer the object, the higher the contrast between light and dark readings, but high-reflectance objects are generally detectable out to around 40 mm. This version features the traditional-style QTR sensors without lenses.
In stock
+
Add to wish list
1 2 3 4 5 6 7 8 9
3 - 17