The 3pi robot is a high performance platform featuring two micro metal gearmotors, five reflectance sensors, an 8×2 character LCD, a buzzer, and three user pushbuttons, all connected to a C-programmable ATmega328 microcontroller. Capable of speeds exceeding 3 feet per second, 3pi is a great first robot for ambitious beginners and a perfect second robot for those looking to move up from non-programmable or slower beginner robots.
This set is intended for those looking to create a differential-drive robot with dual quadrature encoders. The encoder will work with any micro metal gears from Pololu ranging 5:1 to 298:1. Note: Micro metal gears are not included in this set.
These universal aluminum mounting hub allows you to mount custom wheels and mechanisms to 5 mm motor shafts.
This is a 12-inch (30-cm) cable that has three 26 AWG wires attach to a 3-pin female JST PH-style connector.
This is a 12 inch Y splitter cable used to split a single RC hobby servo signal into two identical outputs.
This is a general-purpose programmable module featuring a 2.4 GHz radio and USB. You can write your own software or load precompiled, open-source apps onto the TI CC2511F32 microcontroller at the heart of the Wixel, turning it into a wireless serial link, data logger, or whatever you need for your current project.
This is a shield that allows you to interface Wixel wireless modules to your Arduino (and other compatible products), enabling simple wireless programming, debugging, and control using standard Arduino software.
This is a white pair of micro metal gearmotor bracket extended, which enables convenient mounting of popular Sanyo-style miniature metal gearmotors.
This version of the micro serial servo controller is packaged as a partial kit in which the surface-mounted components are already assembled. Male header pins are included, but you can also connect your servos directly to the PCB if space or weight are a concern.
It is a patented design initially created for the POLOLU Orangutan Robot Controllers as an alternative to bulky mechanical switches.
A discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The little 1.8×0.8-inch board supports a wide 5.5 to 30 V voltage range and is efficient enough to deliver a continuous 25 A without a heat sink.
This tiny carrier board makes it easy to integrate the Sharp GP2Y0D810Z0F and GP2Y0D805Z0F digital distance sensors into your project.
This is an adjustable boost regulator that can generate an output voltage as high as 25 V from an input voltage as low as 1.5 V.
This is a 6mm universal aluminum mounting hub that allows you to mount custom wheels and mechanisms to motor shafts for 6mm diameter.
This S7V7F5 switching step-up/step-down regulator efficiently produces 5 V from input voltages between 2.7 and 11.8 V. Its ability to convert both higher and lower input voltages makes it useful for applications where the power supply voltage can vary greatly, as with batteries that start above but discharge below 5 V.
This is a pair of black silicone tires with plastic tire frames. They fit onto a 3mm D shaft (see related micro motors) and also have mounting holes for mounting hubs as well.
This Kit for Arduino contains most of the parts you need to build an Arduino-controlled Zumo robot. It consists of a Zumo Shield for Arduino, v1.2, a Zumo chassis kit, and a Zumo blade. You will also need a pair of micro metal gearmotors, four AA batteries, and an Arduino to complete your Zumo robot (motors, batteries, and Arduino sold separately). This product is a kit; assembly (including soldering) is required.
These small single-pole, double-throw (SPDT) slide switches are rated for 300 mA at 50 VDC and make great on/off power switches for low power electronics.
The Pololu basic relay carrier modules allow simple control of a single-pole, double-throw (SPDT) switch from low-voltage, low-current control signals.
Can be used with ABRA's male headers SH series and other Pololu male headers. .100" (2.54mm) spacing. .100" x .100" matrix.
These stackable 0.1" (2.54 mm) female headers are just the right height for connecting Arduino shields to Arduinos and other shields. The set includes: Two 1×6 female headers. Two 1×8 female headers. One 1×10 female header.
This is an IDC socket 2x3 female header connector with strain relief clip.
This is a straight double sided 40-pin male header strip that can be use on both sides and also be broken down into smaller strips.
Snap apart to fit your application. Solder to PC boards for instant plug-in access via shorting blocks(ABRA's JUM-1). Can be used with ABRA's female headers FH series or Pololu female headers. .100" x .100" matrix. (2.54mm) Spacing.
This is a single-row right angle 40-pin male header strip that can be broken down into smaller strips.
The extra-long pins have a length of 17.1 mm, which is 5.45 mm longer than typical 0.1" straight male header pins. The standard 0.1" spacing allows use with perforated prototyping PCBs and female headers.
