Our Brands

Makerfabs

1 2 3
Sort Alphabetically: A to Z
15 Per Page
E32S3128GC MaTouch_ESP32-S3 Round SPI TFT with Touch 1.28"
US$40.72
The ESP32-S3 round display with touch can be a great tool for your applications such as smartwatch. We selected the ESP32-S3 generation as the controller, with 16MB Flash and 8MB PSRAM, enough for most IOT applications; The round display is 240x240 resolution 1.28", colorful RGB, with capacitive touch, it communicates with ESP32 with SPI interface, so there enough GPIO left for expansion applications.
In stock
+ −
Add to wish list
E32S319ST MaTouch_ESP32-S3 Parallel TFT with Touch 1.9" ST7789V2
US$45.27
This cute 1.9" display is for IoT applications, it features Wifi/ WiFi& Bluetooth 5.0 + BT mesh, with ESP32-S3R8 Dual-core LX7 microprocessor. This display can be powered by USB or directly by lipo battery, there on-board charger. Also there 2 expansion connectors, with UART/ADC. The colorful display resolution is 320*170, with capacitive touch, which could be a proper solution for IoT applications.
In stock
+ −
Add to wish list
ESP32 UWB (Ultra Wideband) WROVER
US$68.02
Ultra-wideband (UWB) is a short-range, wireless communication protocol that operates through radio waves, enables secure reliable ranging and precision sensing, creating a new dimension of spatial context for wireless devices. Makerfabs ESP32 UWB module is based on DW1000, it acts like a continuously scanning radar, that precisely locks onto another device (called Anchor) and communicates with it, thus calculating its own location. Once the device is near another UWB device, the devices start “ranging.” Ranging refers to calculating the time of flight (ToF) between devices: the roundtrip time of challenge/response packets.
Delivery within 2-3 weeks
+ −
Add to wish list
ESP8266 WIFI Shield
US$11.81
This WiFi Shield based on ESP-12F, which is the new version of the ESP-12 with the Wifi chip ESP8266. With this Shield, you can make your Arduino easy to connect to the network and control your device anywhere. Just communicate via the UART interface and control by AT command.
In stock
+ −
Add to wish list
H-Bridge Motor Shield
US$25.41
This H-Bridge Motor Shield based on 8 N-channel MOSFET IRF3205S and 4 pcs half-bridge motor controller IR2104, to build 2 H-bridge. With this shield, you can control two DC motor with max current up to 8A with 22v voltage at the same time. Also, you can control the motor direction by the logic 0 or 1 with digital pin and speed by the PWM PIN of you MCU, like Arduino. And we support Screw interface, it is easy to connect to the motor and power.
In stock
+ −
Add to wish list
LED-MATRIX-256, WS2812B RGB LED 16x16 Display
US$27.25
The LED-MATRIX-256 is a flexible RGB LED 16x16 Display consisting of a WS2812B RGB LED.
 
In stock
+ −
Add to wish list
LED-MATRIX-64A, WS2812B RGB LED 8x8 Display, Flexible
US$22.52
The LED-MATRIX-64A is a flexible RGB LED 8x8 Display consisting of a WS2812B RGB LED.
 
In stock
+ −
Add to wish list
LED-MATRIX-8X32, WS2812B RGB LED 8x32 Display, Flexible
US$26.16
The LED-MATRIX-64A is a flexible RGB LED 8x8 Display consisting of a WS2812B RGB LED.
 
In stock
+ −
Add to wish list
LOACDI01 Lora AC Dimmer, 915MHz
US$49.82
An AC Dimmer is used to control the AC cycle. Normally, a dimmer is used to turning the power ON/OFF for lamps or heating elements, it can also be used in fans, pumps, air cleaners, etc. Makerfabs Lora AC Dimmer chopper circuit is based on Triac BT139, and zero-cross checking circuit, it detects the zero-cross points and then the Triac controlled to chop the AC. Besides, to avoid the problem of AC can not be totally shunted off with Triac, a relay is implemented to make the AC totally On/Off. On-board AC/DC module implemented, so no external power supply needed, suitable for field applications.
In stock
+ −
Add to wish list
LR20IL Lora Relay 30A 915MHz
US$22.52
This 30A Lora Relay is a relay module that could be controlled by Lora, with max current 30A/240V. Based on RFM98W, it supports a max of 4~5 km Lora communication.
In stock
+ −
Add to wish list
LSMS092D Lora Temperature/ Humidity/ Soil Moisture Sensor 915mhz
US$22.50
The Lora soil moisture sensor is based on Atmel's Atmega328P, it collects local air temperature/ humidity with sensor AHT10, and detect the soil humidity with capacitor-humility measurement solution with 555, and transmit the local environment data to the gateway, with Lora communication, suit for applications for smart-farm, irrigation, agriculture, etc.
In stock
+ −
Add to wish list
MABMPU6050, Mabee_6Aixs IMU MPU6050
US$9.78
The MABMPU6050 is a module with a 3-Axis digital accelerometer and 3-Axis gyroscope, suitable for common motion capturing of acceleration and Orientation.
Delivery within 2-3 weeks
+ −
Add to wish list
MABRELAY, Mabee_Relay 10A
US$4.05
The MABRELAY is a relay module able to handle switching voltages on and off up to 250V at 10A
In stock
+ −
Add to wish list
MABSOIL Mabee_Capacitive Soil Moisture
US$4.50
A simple & cheap capacitive soil moisture sensor, measures the soil moisture level of plants by capacitive sensing.
Delivery within 2-3 weeks
+ −
Add to wish list
MABWIFI, Mabee_Serial WiFi
US$5.41
The MABWIFI is a breakout board based on an ESP-12S chip, that allows you to integrate wireless connections into your projects.
In stock
+ −
Add to wish list
1 2 3