Makerfabs

1 2 3
US$22.50
The Lora soil moisture sensor is based on Atmel's Atmega328P, it collects local air temperature/ humidity with sensor AHT10, and detect the soil humidity with capacitor-humility measurement solution with 555, and transmit the local environment data to the gateway, with Lora communication, suit for applications for smart-farm, irrigation, agriculture, etc.
In stock
+
Add to wish list

US$35.26
This is an MCU module that allows you to create Wifi/GPRS/GPS/BLE connections with your projects by combining an ESP32 and an A9G shield.
In stock
+
Add to wish list

US$27.07
This is a mainboard based on the ATmega328 microchip and Lora Module designed for ultra-long-range, high interference immunity and low rate data transfer. Perfect for IoT projects.
In stock
+
Add to wish list

US$22.52
This 30A Lora Relay is a relay module that could be controlled by Lora, with max current 30A/240V. Based on RFM98W, it supports a max of 4~5 km Lora communication.
In stock
+
Add to wish list

US$113.52
This Maduino Zero 4G LTE module uses the SIMCOM7600(E/A)CAT4 module, to help Makers to achieve the 4G connection easily. Besides, this module can be a fully 4G access to your computer/PI, and also for telephone/SMS...
Delivery within 2-3 weeks
+
Add to wish list

US$68.02
Ultra-wideband (UWB) is a short-range, wireless communication protocol that operates through radio waves, enables secure reliable ranging and precision sensing, creating a new dimension of spatial context for wireless devices. Makerfabs ESP32 UWB module is based on DW1000, it acts like a continuously scanning radar, that precisely locks onto another device (called Anchor) and communicates with it, thus calculating its own location. Once the device is near another UWB device, the devices start “ranging.” Ranging refers to calculating the time of flight (ToF) between devices: the roundtrip time of challenge/response packets.
Delivery within 2-3 weeks
+
Add to wish list

US$40.72
Makerfabs Lora TDS sensor monitors the water status, includes TDS/ temperature, and send the data remotely via Lora, to create a local Lora network, so users can easily create multiple TDS node and process/display them in one Lora server, suitable for applications that need multiple TDS monitor.
In stock
+
Add to wish list

US$90.77
This Industry-grade soil remote monitor intends for these applications of agriculture, it is mainly composed of 2 parts: 1. Remote monitor station with RS485: developed by Makerfabs, it converts the RS485 signal, which is usually used in agricultural field applications, to wireless connections WIFI (if there is) or Lora, or Bluetooth. 2. Industrial-grade Soil Sensor: unlike some other maker-level soil sensors that only output analog voltage that reflects the soil status/changes but not the absolute value, this sensor measures the soil parameters such Temperature/Moisture/PH/Nitrogen/ Phosphorus/Potassium.., with calculated true output, so users can get to know the real soil parameters.
In stock
+
Add to wish list

US$53.46
Power-line communication (PLC) carries data on AC or DC wires. It works by adding a modulated carrier signal to the wiring system. the power distribution system was originally intended for the transmission of AC power at typical frequencies of 50 or 60 Hz, it has only a limited ability to carry higher frequencies, but for some applications such as the sensor monitoring in smart-home, that’s enough.
In stock
+
Add to wish list

US$36.17
This V3.5 is the Newest Version of the Maduino Zero SIM808 GPS Tracker. Maduino Zero SIM808 GPS Tracker is an IoT (Internet of things) Solution based on the 32-bit Atmel’s SAMD21 MCU and GPRS/GSM GPS/Bluetooth module SIM808. It integrates a micro Controller ATSAMD21G18, SIM808, power management, and storage, to make the SIM808 GPS Tracker ready for a real project for IoT projects such as smart-home, outdoor monitoring, shared bicycle, etc. The Maduino Zero SIM808 GPS Tracker based on the Arduino, users can program it with Arduino IDE, which is very easy especially suit for the none-programmers.
In stock
+
Add to wish list

US$49.82
An AC Dimmer is used to control the AC cycle. Normally, a dimmer is used to turning the power ON/OFF for lamps or heating elements, it can also be used in fans, pumps, air cleaners, etc. Makerfabs Lora AC Dimmer chopper circuit is based on Triac BT139, and zero-cross checking circuit, it detects the zero-cross points and then the Triac controlled to chop the AC. Besides, to avoid the problem of AC can not be totally shunted off with Triac, a relay is implemented to make the AC totally On/Off. On-board AC/DC module implemented, so no external power supply needed, suitable for field applications.
In stock
+
Add to wish list

US$22.52
The LED-MATRIX-64A is a flexible RGB LED 8x8 Display consisting of a WS2812B RGB LED.
 
In stock
+
Add to wish list

US$26.16
The LED-MATRIX-64A is a flexible RGB LED 8x8 Display consisting of a WS2812B RGB LED.
 
In stock
+
Add to wish list

US$24.50

MakePython ESP32 is a powerful, generic Wifi+ BLE MCU module target to MicroPython learners & developers. It is true “breadboard compatible”, with the very detailed pins explanation, it is easy to learn& use. The MakePython ESP32 has 2 optional for users: WROOM(NO PSRAM) and WROVER(8MB PSRAM).

In stock
+
Add to wish list

US$40.72
The ESP32-S3 round display with touch can be a great tool for your applications such as smartwatch. We selected the ESP32-S3 generation as the controller, with 16MB Flash and 8MB PSRAM, enough for most IOT applications; The round display is 240x240 resolution 1.28", colorful RGB, with capacitive touch, it communicates with ESP32 with SPI interface, so there enough GPIO left for expansion applications.
In stock
+
Add to wish list
1 2 3